Search found 11949 matches

Go to advanced search

by NormandC
Fri Mar 24, 2017 2:54 am
Forum: Forum français
Topic: Déformer une pièce suivant le profil d'une surface
Replies: 3
Views: 73

Re: Déformer une pièce suivant le profil d'une surface

Salut MacDony, Déformer Bindipiece sur la surface supérieure de Bindisocle. Comme si la pièce était molle Je ne suis pas certain de saisir : la face supérieure de Bindisocle est seulement planaire, avec une légère inclinaison. Ne serait-il pas suffisant d'appliquer une rotation à Bindipiece pour...
by NormandC
Fri Mar 24, 2017 2:35 am
Forum: Forum français
Topic: Vis sans fin
Replies: 11
Views: 148

Re: Vis sans fin

flachyjoe wrote:Comme le profil contient des splines tu ne peux, par contre, pas transformer ça en esquisse

Dans la 0.16. Mais ça devrait être possible sous la 0.17! Déjà, la B-splines a été introduite dans le Sketcher de la version de développement.
by NormandC
Fri Mar 24, 2017 2:31 am
Forum: Part Design module development
Topic: Polar pattern bugs
Replies: 9
Views: 185

Re: Polar pattern bugs

I'm sorry, what are you referring to?
by NormandC
Fri Mar 24, 2017 2:30 am
Forum: Developers corner
Topic: PartDesign Hole feature
Replies: 20
Views: 1032

Re: PartDesign Hole feature

eivindkvedalen wrote:I'm rebasing regularily on my computer, so it's still in good shape

Awesome. :)
by NormandC
Fri Mar 24, 2017 2:21 am
Forum: Help on using FreeCAD
Topic: Strange behaviours on MacOS ?
Replies: 4
Views: 101

Re: Strange behaviours on MacOS ?

Hello Jean-Philippe, Glad you worked it out by yourself with just my couple of pointers! :) Are you aware of a tutorial like "all the dumb things done by beginners" or, better, "all the dumb things thoughts by beginners", because frankly, I did not saw any mistake in my basic sha...
by NormandC
Fri Mar 24, 2017 2:15 am
Forum: Help on using FreeCAD
Topic: Wrongly rendered cylinder on drawing page with Arch Section and Draft Shape2DView
Replies: 9
Views: 225

Re: Wrongly rendered cylinder on drawing page with Arch Section and Draft Shape2DView

I confirm the Drawing view shows the cylinder correctly in the following version. But first you must force recompute the document. I use the Macro ForceRecompute . OS: Ubuntu 16.04.2 LTS Word size of OS: 64-bit Word size of FreeCAD: 64-bit Version: 0.17.10611 (Git) Build type: None Branch: master Ha...
by NormandC
Fri Mar 24, 2017 2:10 am
Forum: Help on using FreeCAD
Topic: Title Block edit in Drawing Dimensioning WB
Replies: 23
Views: 243

Re: Title Block edit in Drawing Dimensioning WB

Hello Brian, Is there something I should do to close the thread? It is not a custom here, but if you want you can edit your first message in this topic, and add [Solved] at the start of the Subject line. I see a "Insert Annotation View"button on the Drawing Dimensioning WB, but haven't fou...
by NormandC
Fri Mar 24, 2017 2:03 am
Forum: Developers corner
Topic: appimage
Replies: 115
Views: 3048

Re: appimage

NormandC wrote:EDIT: is the path where the AppImage is built important? I built it in a sub-folder 3 levels below my Home folder.

... And that was it. :roll:

After building a new AppImage directly in $HOME, I can launch the binary.

Thank you triplus for asking the obvious question...
by NormandC
Fri Mar 24, 2017 1:30 am
Forum: Install / Compile
Topic: [Ubuntu Daily PPA] Transitioning to OCCT7, VTK7...
Replies: 222
Views: 8714

Re: [Ubuntu Daily PPA] Transitioning to OCCT7, VTK7...

sgrogan wrote:I'm only "Approved" so i can't handle 4

Say that again? ;)
by NormandC
Fri Mar 24, 2017 1:15 am
Forum: Developers corner
Topic: appimage
Replies: 115
Views: 3048

Re: appimage

What could I have possibly done differently when all that is required is to copy-paste the two same commands posted here that you and sgrogan have most probably used? https://forum.freecadweb.org/viewtopic.php?f=10&t=15525&start=20#p152068 I used the FreeCAD-nightly recipe. EDIT: is the path...

Go to advanced search