Search found 52957 matches
- Fri Mar 29, 2024 9:31 pm
- Forum: Help on using FreeCAD
- Topic: Point-object coincident constraint
- Replies: 2
- Views: 114
Re: Point-object coincident constraint
Is there a way to tell FreeCAD the difference between "move the point to the object" and "move the object to the point" with this constraint? Reading the documentation it would seem that there isn't. You are right, there isn't. And in theory it should make no difference anyway, ...
- Fri Mar 29, 2024 8:54 pm
- Forum: UX/UI Design
- Topic: A new take on the UI. FreeCAD Nut.
- Replies: 130
- Views: 201815
Re: A new take on the UI. FreeCAD Nut.
Moderation has to be more than just focused around civility, which even that has been lackadaisically enforced in the past. ... Here is another example, I requested no comments outside of submitting artwork. First response was a moderator questioning the need for a new thread despite my request bei...
- Fri Mar 29, 2024 9:23 am
- Forum: Help on using FreeCAD
- Topic: [ Fixed ] Can't create PD datums with a pre-selection?
- Replies: 8
- Views: 252
- Fri Mar 29, 2024 9:18 am
- Forum: Forum in Deutsch
- Topic: stable- und Entwickler-Version parallel - gleiche Voreinstellungen?
- Replies: 3
- Views: 177
Re: stable- und Entwickler-Version parallel - gleiche Voreinstellungen?
Beim Snap-Paket weiß ich nicht, wie weit die Abschottung geht. Ansonsten ist es normal auf dieselbe config-Datei zuzugreifen. Sinnvoll musst Du selbst entscheiden.
Es kann allerdings auch mal Konflikte geben, wenn Eigenschaften dazukommen, also immer ein Backup für beide Versionen parat halten.
Es kann allerdings auch mal Konflikte geben, wenn Eigenschaften dazukommen, also immer ein Backup für beide Versionen parat halten.
- Fri Mar 29, 2024 8:44 am
- Forum: Help on using FreeCAD
- Topic: [ Fixed ] Can't create PD datums with a pre-selection?
- Replies: 8
- Views: 252
- Fri Mar 29, 2024 8:21 am
- Forum: Help on using FreeCAD
- Topic: [ Fixed ] Can't create PD datums with a pre-selection?
- Replies: 8
- Views: 252
Re: Can't create PD datums with a pre-selection?
I don't use PartDesign datums every day, but I was a bit surprised that they can't be created with a pre-selection. The error message is confusing: "There are no attachment modes that fit selected objects. Select something else." All pre-selections are simply ignored AFAICT. Or am I missi...
- Fri Mar 29, 2024 8:18 am
- Forum: Forum in Deutsch
- Topic: in Part Variante erstellen
- Replies: 2
- Views: 103
Re: in Part Variante erstellen
Dafür gibt es die Configuration tables.
- Fri Mar 29, 2024 6:32 am
- Forum: Help on using FreeCAD
- Topic: still struggling to understand the modeling process of freecad
- Replies: 23
- Views: 743
Re: still struggling to understand the modeling process of freecad
i draw a circle, hit P, then pull(extrude) the circle up and if i just type a number, lets say 6.5" it will extrude it to exactly 6.5 inches. Then if i hit F, and click the top surface it will offset the surface by what ever number and unit i type in. Now if i hit P again and grab the center o...
- Fri Mar 29, 2024 6:01 am
- Forum: Help on using FreeCAD
- Topic: Cutting out multiple objects with paths
- Replies: 4
- Views: 222
Re: Cutting out multiple objects with paths
There is no job in your model, so we don't know what you tried. - Note, that a pocket will fail, if the tool has exactly the diameter of the distance between the squares. - To get this done with an optimized path milling always from end to end, you may need further helper sketches and e.g. pretend t...
- Fri Mar 29, 2024 5:51 am
- Forum: UX/UI Design
- Topic: A new take on the UI. FreeCAD Nut.
- Replies: 130
- Views: 201815