Search found 2926 matches
- Wed Jun 12, 2019 11:39 am
- Forum: Help on using FreeCAD
- Topic: [Solved] Arbitrary cone
- Replies: 13
- Views: 2552
Re: Arbitrary cone
read the wiki, its all explained there and is too complex to just endlessly repeat on the forum. Ok, for me yelling you're here, and to send them ...swear word removed again, by moderator.... too :mrgreen: and if Google translat to accept to translate is that the words are "politically" c...
- Wed Jun 12, 2019 11:34 am
- Forum: Help on using FreeCAD
- Topic: Sketch Freecad 0.19 some not editable but are visible
- Replies: 4
- Views: 1272
Re: Sketch Freecad 0.19 some not editable but are visible
Salut
You a little load the mule as we say at home,
as you're french, you do not want to go to the french forum that we talk about it between us and we simplify a little bit
You a little load the mule as we say at home,
as you're french, you do not want to go to the french forum that we talk about it between us and we simplify a little bit
- Wed Jun 12, 2019 7:41 am
- Forum: Help on using FreeCAD
- Topic: [Solved] Arbitrary cone
- Replies: 13
- Views: 2552
Re: Arbitrary cone
Right, so what is the right method?Perhaps meme2704 was thinking about the Sketcher point, which indeed cannot be used for such a loft, as it is only construction geometry.
- Wed Jun 12, 2019 7:36 am
- Forum: Help on using FreeCAD
- Topic: Integrating a nut into a cylinder shaped form
- Replies: 5
- Views: 1223
Re: Integrating a nut into a cylinder shaped form
Hi
You draw the body of the bochon, you place the holes in the right place with a chamfer, you put the 3 screws in the holes and you make a Boolean subtraction
You draw the body of the bochon, you place the holes in the right place with a chamfer, you put the 3 screws in the holes and you make a Boolean subtraction
- Wed Jun 12, 2019 6:04 am
- Forum: Help on using FreeCAD
- Topic: Cutting walled cylinders intersection
- Replies: 6
- Views: 1327
Re: Cutting walled cylinders intersection
Hi
The sketches of the tubes are not constrained, they only need a few microns of difference to see this defect
The sketches of the tubes are not constrained, they only need a few microns of difference to see this defect
- Tue Jun 11, 2019 4:54 pm
- Forum: Help on using FreeCAD
- Topic: [SOLVED] Map sketch to face
- Replies: 7
- Views: 2738
Re: Map sketch to face
Hi
Base is an empty sketch, Why
Channels is composed of crossed lines, unsupported (self_intersection)
After some repairs I reconstituted your drawing
Base is an empty sketch, Why
Channels is composed of crossed lines, unsupported (self_intersection)
After some repairs I reconstituted your drawing
- Tue Jun 11, 2019 10:47 am
- Forum: Help on using FreeCAD
- Topic: [Solved] Arbitrary cone
- Replies: 13
- Views: 2552
Re: Arbitrary cone
Hi
The answer is yes, except that a point is not recognized, it is necessary to create a mini circle (r = 0.01mm)
The answer is yes, except that a point is not recognized, it is necessary to create a mini circle (r = 0.01mm)
- Tue Jun 11, 2019 10:35 am
- Forum: Help on using FreeCAD
- Topic: additivePipe usage
- Replies: 6
- Views: 1295
Re: additivePipe usage
I remove the structural tubes and I get renfort-2
I make a finished carbon copy the internal radii and I get renfort-3
I made a carbon copy because only one file is too big
I make a finished carbon copy the internal radii and I get renfort-3
I made a carbon copy because only one file is too big
- Mon Jun 10, 2019 3:14 pm
- Forum: Help on using FreeCAD
- Topic: Sketches have disappeared?
- Replies: 6
- Views: 1529
Re: Sketches have disappeared?
When you are told that deforestation is putting the planet at risk there is still some septic to refuse it, so
If you did not save the Fc file, it is not recoverable, what did you save
If you did not save the Fc file, it is not recoverable, what did you save
- Mon Jun 10, 2019 2:44 pm
- Forum: Help on using FreeCAD
- Topic: printer friendly version of a sketch.
- Replies: 20
- Views: 3129
Re: printer friendly version of a sketch.
Preferance /color you can change screen from black to with , and lign for black