Search found 951 matches
- Mon Apr 08, 2024 2:52 am
- Forum: Path/CAM
- Topic: 3D path - need select finish process only
- Replies: 7
- Views: 545
Re: 3D path - need select finish process only
... Sample interval - it just for visualization ? correct ? - it no matter for real trajectory ? ... Evening, The Sample Interval does affect the actual paths calculated and seen. However, if you need to adjust or tinker with various settings for a 3D Surface op, then one strategy to reduce calcula...
- Sun Apr 07, 2024 11:05 pm
- Forum: Path/CAM
- Topic: 3D path - need select finish process only
- Replies: 7
- Views: 545
Re: 3D path - need select finish process only
Hi Russel - id works, in my model also need to on Optimize StepOver Transitions - because some wird up and down trajectory lines creates(on bottom of perimeter mount). ... Afternoon, Thanks for the cookies. The frequent retraction-plunge pairs around a given path at height are due to the calculatio...
- Sun Apr 07, 2024 3:34 am
- Forum: Path/CAM
- Topic: Profile Single Face Error
- Replies: 8
- Views: 565
Re: Profile Single Face Error
The green face is the one I want to select: ... Evening, When wanting to profile open edges (non-closed wires), the Profile op requires selection of edges - see usage notes in the CAM_Profile wiki. The edges should be the top edges along the desired profile, then the Final Depth will need to be set...
- Sun Apr 07, 2024 2:25 am
- Forum: Path/CAM
- Topic: Unadulterated Custom G-Code?
- Replies: 6
- Views: 499
Re: Unadulterated Custom G-Code?
Is there a way to create a custom g-code entry in a Path Job? I have tried using the "Custom" op but is keeps modifying the code making it inoperable. How do I tell it to use the code exactly as is? ... Evening and welcome to the forum! I shall post a non-official, and unexperienced reply...
- Sun Apr 07, 2024 2:11 am
- Forum: Path/CAM
- Topic: 3D path - need select finish process only
- Replies: 7
- Views: 545
Re: 3D path - need select finish process only
... How to create operation only for mount ? Good evening. Welcome back to the forum. Please see the attached screenshot and source file, from FreeCAD 20.2. Use 3D Surface operation. This example uses stock 6.0mm ball end mill. Select the cone and top-of-cone faces. Change Step Down value to about ...
- Thu Apr 04, 2024 12:12 am
- Forum: Path/CAM
- Topic: Path Engrave generates multiple passes for edges
- Replies: 7
- Views: 562
Re: Path Engrave generates multiple passes for edges
... has the problem been fixed in the latest release, or the fix coming up in a future one? Pertaining to the latest release, I do not know because I have not tested. Pertaining to future release fix, I do not have an answer. I am not a member of any FreeCAD planning or steering committees. One of ...
- Wed Apr 03, 2024 12:59 am
- Forum: Path/CAM
- Topic: Path Engrave generates multiple passes for edges
- Replies: 7
- Views: 562
Re: Path Engrave generates multiple passes for edges
[Problem] CAM: Engraving duplicates gcode for some base elements #9303munther_hindi wrote: ↑Tue Apr 02, 2024 2:18 pm The Path Engrave operation generates multiple passes for the same edge/wire, depending on how the wires are added to the Base Geometry.
...
Respectfully,
Russell
- Sun Mar 31, 2024 8:17 pm
- Forum: Path/CAM
- Topic: How can I access Start Depth, Safe Height in a postprocessor?
- Replies: 19
- Views: 1224
Re: How can I access Start Depth, Safe Height in a postprocessor?
... Where can I find the definitions of these objects , ... ? Cheers. Afternoon, Here is the generic property list for ToolController objects attached to path objects - taken specifically from the default 5.0 mm endmill tool controller. ExpressionEngine HorizFeed HorizRapid Label Label2 Path Placem...
- Sun Mar 31, 2024 2:24 pm
- Forum: Path/CAM
- Topic: How can I access Start Depth, Safe Height in a postprocessor?
- Replies: 19
- Views: 1224
Re: How can I access Start Depth, Safe Height in a postprocessor?
... I wanted to use fraction of the drill diameter but it did not seem to be available ... Morning, A modification would need to be made to the code. I suggest passing the tool controller, or even the Path object itself, to the 'drill_translate()' function, then you will have access to drill diamet...
- Sat Mar 30, 2024 4:51 pm
- Forum: Path/CAM
- Topic: How can I access Start Depth, Safe Height in a postprocessor?
- Replies: 19
- Views: 1224
Re: How can I access Start Depth, Safe Height in a postprocessor?
I try to tune up the grbl_post.py postprocessor (speed, G73, correct implementation of G98 / G99) Is it possible to access the "Safe Height" and the "Start Depth" settings in Drilling Operations Property from the postprocessor script? ... Good morning. Generally speaking, using ...