Search found 12 matches

Go to advanced search

by glabifrons
Sun Feb 02, 2020 9:31 pm
Forum: Help on using FreeCAD
Topic: Tracker account creation - no confirmation email sent
Replies: 10
Views: 187

Re: Tracker account creation - no confirmation email sent

chrisb wrote:
Sun Feb 02, 2020 6:21 am
I wanted to test it on my own account and could not find a setting for sending the contents. Where did you set it?
You can find it here:
Control Panel -> Board preferences -> Edit notification options
by glabifrons
Sun Feb 02, 2020 1:10 am
Forum: Help on using FreeCAD
Topic: Tracker account creation - no confirmation email sent
Replies: 10
Views: 187

Re: Tracker account creation - no confirmation email sent

I sent you a private message. Usually you should get an email now. If not, please check your configuration in your forum control panel. Much appreciated. I did receive an email notification for your PM, but not your posted reply (both are enabled in my notification options). So at least it's not th...
by glabifrons
Sun Feb 02, 2020 12:28 am
Forum: Help on using FreeCAD
Topic: Tracker account creation - no confirmation email sent
Replies: 10
Views: 187

Re: Tracker account creation - no confirmation email sent

Update: It appears I'm also not getting emails from this forum either anymore, as the last one was from last May. I should have received a notification of a reply to another topic almost 7 hours ago, plus the one from a few minutes ago in this topic. It's possible that something has been reconfigure...
by glabifrons
Sun Feb 02, 2020 12:17 am
Forum: Help on using FreeCAD
Topic: Cannot name a reference dimension in 0.18
Replies: 5
Views: 177

Re: Cannot name a reference dimension in 0.18

Roy_043 wrote:
Sat Feb 01, 2020 5:19 pm
Confirmed. To avoid the problem double-click the constraint in the Constraint section of the Sketcher Task panel. You can also rename a constraints by right-clicking it in the Task panel.
Thank you very much! That's a good workaround.
by glabifrons
Sun Feb 02, 2020 12:10 am
Forum: Help on using FreeCAD
Topic: Tracker account creation - no confirmation email sent
Replies: 10
Views: 187

Tracker account creation - no confirmation email sent

I tried to create an account on https://tracker.freecadweb.org/signup.php and it informed me that it sent a confirmation email, and if I don't confirm that my account will be purged. This was several hours ago, and I've still not received the confirmation email (I used the same address as I used for...
by glabifrons
Sat Feb 01, 2020 4:24 pm
Forum: Help on using FreeCAD
Topic: Cannot name a reference dimension in 0.18
Replies: 5
Views: 177

Cannot name a reference dimension in 0.18

When creating a reference dimension, there is no prompt (so you cannot add a name). When trying to edit the reference dimension to give it a name, it converts it to a constraint. If the drawing is already fully constrained, it displays an error that it is an invalid constraint. If you start with a c...
by glabifrons
Thu May 16, 2019 2:01 am
Forum: Help on using FreeCAD
Topic: SpaceBall rotation stops when focus leaves main display panel in v0.18
Replies: 5
Views: 293

Re: SpaceBall rotation stops when focus leaves main display panel in v0.18

I'm not sure why it wasn't working before, but measuring doesn't stop the spaceball from rotating (I swear it was when I tested before). However, clicking in any of the panels still does stop rotation. I tested with the Combo View panel with all navigation styles, then with Blender selected, I tried...
by glabifrons
Sun May 12, 2019 6:04 am
Forum: Help on using FreeCAD
Topic: SpaceBall rotation stops when focus leaves main display panel in v0.18
Replies: 5
Views: 293

SpaceBall rotation stops when focus leaves main display panel in v0.18

Does anyone know if there is now a setting for the SpaceBall to only function when focus is on the display panel? If so, do you know how to revert to the 0.17 (and prior) behavior? I couldn't find any relevant settings in the parameter editor. As soon as you click into any other panel (or menu), you...
by glabifrons
Tue Aug 14, 2018 4:25 am
Forum: Help on using FreeCAD
Topic: Lattice2 more restrictive in 0.17? (globoid worm drive attempt)
Replies: 8
Views: 320

Re: Lattice2 more restrictive in 0.17? (globoid worm drive attempt)

Actually, this works nicely! Thanks! I added a spreadsheet to automatically calculate the spread and angle of the PolarArray based on the specified number of teeth (so you don't have to edit each field each time you make a change), dimensioned the sketch, changed the radius to 8.5, the modulus to 0....
by glabifrons
Sun Aug 12, 2018 4:55 am
Forum: Help on using FreeCAD
Topic: Lattice2 more restrictive in 0.17? (globoid worm drive attempt)
Replies: 8
Views: 320

Re: Lattice2 more restrictive in 0.17? (globoid worm drive attempt)

Thanks :oops: I totally missed that.
I've attached both attempts.

Go to advanced search