Search found 3606 matches

Go to advanced search

by papyblaise
Thu Jun 17, 2021 11:16 am
Forum: Help on using FreeCAD
Topic: Erro no polarPattern
Replies: 3
Views: 102

Re: Erro no polarPattern

as Roy says, there is indeed a fatal error for using PartDesign, but it might be good for bad because you are actually working in PartWB so if you continue in Part, the miror may be use in all major axes, but also by setting an offset of the origin, and also following an arbitrary line drawn before ...
by papyblaise
Wed Jun 16, 2021 4:14 pm
Forum: Help on using FreeCAD
Topic: Use draft / array to make holes in Part Design
Replies: 28
Views: 695

Re: Use draft / array to make holes in Part Design

good, good if you prefer the classic: 2500holes:
2mn50 "with Partdesignet a 760mb file
1mn and 306mo with Draft array
so there is no equal
by papyblaise
Wed Jun 16, 2021 2:18 pm
Forum: Help on using FreeCAD
Topic: Cutting in sweep destroys part
Replies: 4
Views: 147

Re: Cutting in sweep destroys part

it is often only a visual defect, if you do a subtractiv pipe, in general it works
but without file, no definitive answer
by papyblaise
Wed Jun 16, 2021 2:13 pm
Forum: Help on using FreeCAD
Topic: Use draft / array to make holes in Part Design
Replies: 28
Views: 695

Re: Use draft / array to make holes in Part Design

always these phony excuses, and each time I evoke this figure, I receive a fall of mockery, I nevertheless find this form nice :lol:
by papyblaise
Wed Jun 16, 2021 11:47 am
Forum: Help on using FreeCAD
Topic: Use draft / array to make holes in Part Design
Replies: 28
Views: 695

Re: Use draft / array to make holes in Part Design

not more! This is fixed in 0.20dev
I would like to believe you, here is an example
1600 spiral holes: with part 2.5mn, with Partdesign: crash after 10mn
I warn: wear sunglasses, because it makes the eyes spiral too :lol:
Fc V20pre
by papyblaise
Wed Jun 16, 2021 6:59 am
Forum: Help on using FreeCAD
Topic: File breakage when using FreeCAD 0.19
Replies: 3
Views: 130

Re: File breakage when using FreeCAD 0.19

at home, sketch is empty :!:
Did you delete it by mistake :?:
by papyblaise
Tue Jun 15, 2021 9:04 pm
Forum: Help on using FreeCAD
Topic: Use draft / array to make holes in Part Design
Replies: 28
Views: 695

Re: Use draft / array to make holes in Part Design

Ha that reassures me I'm not alone :!:
by papyblaise
Tue Jun 15, 2021 7:03 pm
Forum: Help on using FreeCAD
Topic: Sheet Metal Workbench
Replies: 407
Views: 64936

Re: Sheet Metal Workbench

yes it is obviously, when we have the chance to work in an old factory, we always find in the scrap heap the old bending tool of which we can recover the appropriate length :!:
by papyblaise
Tue Jun 15, 2021 3:50 pm
Forum: Help on using FreeCAD
Topic: Use draft / array to make holes in Part Design
Replies: 28
Views: 695

Re: Use draft / array to make holes in Part Design

we have already mentioned it dozens of times here: Partdesign Multitransform works to duplicate a few holes, but as soon as you want to have 20 or 30 (and more) it becomes impossible
Draft Array has no limits (maybe where flat earth ends :lol: :lol: :lol: )

Go to advanced search