Search found 8015 matches
- Tue Apr 23, 2024 9:41 am
- Forum: Help on using FreeCAD
- Topic: Joining two cylinders at an angle
- Replies: 7
- Views: 301
Re: Joining two cylinders at an angle
Edit of Edit : delete your other post since it was answered here
- Tue Apr 23, 2024 9:25 am
- Forum: Help on using FreeCAD
- Topic: Joining two cylinders at an angle
- Replies: 7
- Views: 301
Re: Joining two cylinders at an angle
if you want you can do a zigzag
don't forget to specify "transition > right corners"
Edit: With the latest version, there is no more self intersection with "Round corner" good news
don't forget to specify "transition > right corners"
Edit: With the latest version, there is no more self intersection with "Round corner" good news
- Tue Apr 23, 2024 9:12 am
- Forum: Help on using FreeCAD
- Topic: Sheet metal extend to create angled edge for slope-faced cabinet
- Replies: 8
- Views: 384
Re: Sheet metal extend to create angled edge for slope-faced cabinet
I understood what you want
I don't start with PartDesign, that causes problems when you have cuts to make, so I use Sketcher and SheetMetal, if necessary PartWb for angled cuts
I don't start with PartDesign, that causes problems when you have cuts to make, so I use Sketcher and SheetMetal, if necessary PartWb for angled cuts
- Tue Apr 23, 2024 8:07 am
- Forum: Forum français
- Topic: Se dépanner d'un problème freecad
- Replies: 5
- Views: 167
Re: Se dépanner d'un problème freecad
quand tu fais "Copier" une fenètre s'ouvre et te montre tous ce qui est susceptible d'être copier , tu décoche ce que tu veux pas emmener et fouette cocher , mais t'inquiète pas si t'as deux fois le plan XY , le second ne gènera pas si c'est pour faire un système à glissières à double queu...
- Mon Apr 22, 2024 3:56 pm
- Forum: Help on using FreeCAD
- Topic: Fusion not working fully/properly?
- Replies: 22
- Views: 805
Re: Fusion not working fully/properly?
I reread the entire post until my eyes bleed, but I don't see a file anywhere
- Sun Apr 21, 2024 1:30 pm
- Forum: Help on using FreeCAD
- Topic: Sheet metal extend to create angled edge for slope-faced cabinet
- Replies: 8
- Views: 384
Re: Sheet metal extend to create angled edge for slope-faced cabinet
everything goes well up to "BaseWall" why do an extrusion over the already existing folding
- Sun Apr 21, 2024 1:03 pm
- Forum: Forum français
- Topic: TechDraw : comment faire pour coter en mètre et non en millimètres ??
- Replies: 5
- Views: 277
Re: TechDraw : comment faire pour coter en mètre et non en millimètres ??
ha oui Ok , mais fouchtrah ça marche pas , ça passe en inch, en Ft, en cm arch mais pas en m
- Sun Apr 21, 2024 11:16 am
- Forum: Forum français
- Topic: TechDraw : comment faire pour coter en mètre et non en millimètres ??
- Replies: 5
- Views: 277
Re: TechDraw : comment faire pour coter en mètre et non en millimètres ??
qu'est ce que tu montre là ? le panneau dimensions dans Préférence ? Ben non , ça marche pas : les dim sont bien en m dans sketcher , mais pas dans Techdraw , enfin , chez moi ça marche pas D'ailleurs les dim en m , on peut les mettre dans Sketcher : il suffit d'effacer un m dans la fenètre de cotat...
- Sun Apr 21, 2024 10:16 am
- Forum: Help on using FreeCAD
- Topic: Failure to create Fillet
- Replies: 3
- Views: 424
Re: Failure to create Fillet
turning around, I ended up wearing it out
I didn't do the R between the 2 legs in the sketch and I did the fillets side by side
for large faces: an R=0.9 works
in my file I still have to make the green fillets
I didn't do the R between the 2 legs in the sketch and I did the fillets side by side
for large faces: an R=0.9 works
in my file I still have to make the green fillets
- Sun Apr 21, 2024 9:24 am
- Forum: Help on using FreeCAD
- Topic: Fusion not working fully/properly?
- Replies: 22
- Views: 805
Re: Fusion not working fully/properly?
I don't understand what you did, it's done in a Body without addition or subtraction