Search found 13 matches

Go to advanced search

by torvictech
Wed Feb 05, 2020 6:09 pm
Forum: Job offers
Topic: Need assistance designing a tool
Replies: 30
Views: 2537

Re: Need assistance designing a tool

Turned out good (my camera image is too large, so I will post later from home). Now I just have to test it - I will let you know how it goes and provide you with feedback.
by torvictech
Tue Feb 04, 2020 8:42 pm
Forum: Job offers
Topic: Need assistance designing a tool
Replies: 30
Views: 2537

Re: Need assistance designing a tool

Great, I will print later tonight and send you prints. :)
by torvictech
Tue Feb 04, 2020 8:08 pm
Forum: Job offers
Topic: Need assistance designing a tool
Replies: 30
Views: 2537

Re: Need assistance designing a tool

Just to be sure, cut-out means a complete material removal from hole up to side ? Yes, that is right and if you can please ensure that the solid border is there too that would be great. I don't know if my 3D printer prints different colors, so for now same color should be fine ;) I will take a pict...
by torvictech
Tue Feb 04, 2020 6:29 pm
Forum: Job offers
Topic: Need assistance designing a tool
Replies: 30
Views: 2537

Re: Need assistance designing a tool

Last adjustments, before print :D 1. Add the solid border around the top hole 2. Move the hole up, as per attachment 3. Create cut-out from hole (from bottom/right side of the hole - eg. can continue the hottom of hole all the way out) to the right side (for easy sliding in/out) 4. Move logo down an...
by torvictech
Tue Feb 04, 2020 4:24 pm
Forum: Job offers
Topic: Need assistance designing a tool
Replies: 30
Views: 2537

Re: Need assistance designing a tool

Almost there...would it be possible to perhaps record a video/screen session as you design this, so that if i need to make some small adjustments i can see how to make them? Thanks so much. Vic
by torvictech
Mon Feb 03, 2020 11:21 pm
Forum: Job offers
Topic: Need assistance designing a tool
Replies: 30
Views: 2537

Re: Need assistance designing a tool

Nice, yes we are definitely getting there. With the 'arch' I was hoping that the entire shape can be arched, just like I have noted in the new attachment. In essence, the back of the tool is not flat, but has an arch as the front. Also can all the sides of the tool have 'filleted' edges with an angl...
by torvictech
Mon Feb 03, 2020 10:00 pm
Forum: Job offers
Topic: Need assistance designing a tool
Replies: 30
Views: 2537

Re: Need assistance designing a tool

Now I'm not sure I well understood your sketch. Is the center square a pocket with embossed logo ? Or solid material with engraved logo ? Answer: It's the reverse of what you have, essentially a solid part within the waffle grid, with the logo engraved in the solid part. Can this shape be considere...
by torvictech
Mon Feb 03, 2020 9:42 pm
Forum: Job offers
Topic: Need assistance designing a tool
Replies: 30
Views: 2537

Re: Need assistance designing a tool

Please see all answers below: Regarding the hole, what is the distance from the rear face ? What is its height ? Answer: Distance from the top is 5mm; the height is 5mm; Regarding the square pocket around the logo, what is its size (width/height) ? Position (X/Y) ? Answer: Either 10mm x 10mm or 15mm...
by torvictech
Mon Feb 03, 2020 9:10 pm
Forum: Job offers
Topic: Need assistance designing a tool
Replies: 30
Views: 2537

Re: Need assistance designing a tool

...also, the entire item has a slight bend/shape to it as per the "red" line on the image from top to bottom, as oriented via the logo on the front of it.
Thx, Vic.
by torvictech
Mon Feb 03, 2020 8:53 pm
Forum: Job offers
Topic: Need assistance designing a tool
Replies: 30
Views: 2537

Re: Need assistance designing a tool

It's a perforated square surface. The depth of the holes is 1mm, leaving 2mm of solid layer below - given that the depth of the item is 3mm.
Thx, Vic.

Go to advanced search