Search found 37303 matches

by chrisb
Wed Oct 27, 2021 6:07 am
Forum: Help on using FreeCAD
Topic: How to make threaded holes.
Replies: 10
Views: 388

Re: How to make threaded holes.

This was reported recently, but I couldn't find a ticket.
by chrisb
Wed Oct 27, 2021 6:00 am
Forum: Help on using FreeCAD
Topic: 'nan' is not defined
Replies: 1
Views: 79

Re: 'nan' is not defined

You have created somehow a line o an arc of zero length - probably by doing some indefinite clicking. You must fix this before continuing, because otherwise the solver gets out of whack.
by chrisb
Tue Oct 26, 2021 11:09 pm
Forum: Help on using FreeCAD
Topic: Misalignment on polar pattern?
Replies: 9
Views: 297

Re: Misalignment on polar pattern?

domad wrote: Tue Oct 26, 2021 7:26 pm the other a little neater in the modeling flow.
Is there a certain reason why you left most sketches unattached?
by chrisb
Tue Oct 26, 2021 10:08 pm
Forum: Install / Compile
Topic: Running FreeCAD from a Network Drive?
Replies: 2
Views: 142

Re: Running FreeCAD from a Network Drive?

I would like to run FreeCAD from a network drive so that I can do the main design work on a PC in the office, then go to the workshop an use a Notebook to monitor the CNC output. I have trawled through the forum and "tried" to follow what has been said about [SOLVED] Portable FreeCAD(user...
by chrisb
Tue Oct 26, 2021 7:22 pm
Forum: Forum in Deutsch
Topic: Fehler in der Simulation?
Replies: 5
Views: 229

Re: Fehler in der Simulation?

M4x wrote: Tue Oct 26, 2021 5:34 pm Wenn du Path nutzen möchtest, unbedingt die aktuelle development Version 0.20 nutzen. Auch im Allgemeinen sehr zu empfehlen.
Das ist die richtige Empfehlung; es wird allerdings wahrscheinlich am Simulator nichts ändern.
by chrisb
Tue Oct 26, 2021 7:19 pm
Forum: Python scripting and macros
Topic: Run an in-memory macro as if run by MacroManager
Replies: 13
Views: 633

Re: Run an in-memory macro as if run by MacroManager

TheMarkster wrote: Tue Oct 26, 2021 3:53 pm Does it also fail on linux and mac?
I admit that I didn't follow this topic. What exactly can/should I test?
by chrisb
Tue Oct 26, 2021 4:46 pm
Forum: Help on using FreeCAD
Topic: help about drawing
Replies: 12
Views: 502

Re: help about drawing

Can't resist either:
heda wrote: Tue Oct 26, 2021 3:36 pm any code that works is good code
No!
by chrisb
Tue Oct 26, 2021 4:44 pm
Forum: Forum in Deutsch
Topic: Array lässt sich nicht mit Booleschen Operation abziehen
Replies: 9
Views: 203

Re: Array lässt sich nicht mit Booleschen Operation abziehen

Ohne die Datei ist es schwer etwas zu sagen, aber bei der Verwendung von Part-Funktionen musst Du immer den gesamten Body auswählen, nicht nur ein Feature daraus.
by chrisb
Tue Oct 26, 2021 4:40 pm
Forum: Help on using FreeCAD
Topic: Misalignment on polar pattern?
Replies: 9
Views: 297

Re: Misalignment on polar pattern?

Fillet, Chamfer and Draft are rather dressups, and as such the patterns need the feature which is dressed up as well.
by chrisb
Tue Oct 26, 2021 11:57 am
Forum: Forum in Deutsch
Topic: Kantteile modellieren
Replies: 8
Views: 398

Re: Kantteile modellieren

Das Problem mit einem Loft ist, dass es auch bei gleichbleibender Stärke mit der SheetMetal-Workbench nicht mehr flachgelegt werden kann, weil die Flächen B-Spline-Oberflächen werden. Geometriefehler wie z.B. bei Shalmeneser tun dann ihr Übriges. Ich würde tatsächlich SheetMetal versuchen und dann Ü...