Search found 37301 matches

by chrisb
Tue Oct 26, 2021 11:09 pm
Forum: Help on using FreeCAD
Topic: Misalignment on polar pattern?
Replies: 8
Views: 258

Re: Misalignment on polar pattern?

domad wrote: Tue Oct 26, 2021 7:26 pm the other a little neater in the modeling flow.
Is there a certain reason why you left most sketches unattached?
by chrisb
Tue Oct 26, 2021 10:08 pm
Forum: Install / Compile
Topic: Running FreeCAD from a Network Drive?
Replies: 1
Views: 96

Re: Running FreeCAD from a Network Drive?

I would like to run FreeCAD from a network drive so that I can do the main design work on a PC in the office, then go to the workshop an use a Notebook to monitor the CNC output. I have trawled through the forum and "tried" to follow what has been said about [SOLVED] Portable FreeCAD(user...
by chrisb
Tue Oct 26, 2021 7:22 pm
Forum: Forum in Deutsch
Topic: Fehler in der Simulation?
Replies: 5
Views: 206

Re: Fehler in der Simulation?

M4x wrote: Tue Oct 26, 2021 5:34 pm Wenn du Path nutzen möchtest, unbedingt die aktuelle development Version 0.20 nutzen. Auch im Allgemeinen sehr zu empfehlen.
Das ist die richtige Empfehlung; es wird allerdings wahrscheinlich am Simulator nichts ändern.
by chrisb
Tue Oct 26, 2021 7:19 pm
Forum: Python scripting and macros
Topic: Run an in-memory macro as if run by MacroManager
Replies: 13
Views: 606

Re: Run an in-memory macro as if run by MacroManager

TheMarkster wrote: Tue Oct 26, 2021 3:53 pm Does it also fail on linux and mac?
I admit that I didn't follow this topic. What exactly can/should I test?
by chrisb
Tue Oct 26, 2021 4:46 pm
Forum: Help on using FreeCAD
Topic: help about drawing
Replies: 12
Views: 489

Re: help about drawing

Can't resist either:
heda wrote: Tue Oct 26, 2021 3:36 pm any code that works is good code
No!
by chrisb
Tue Oct 26, 2021 4:44 pm
Forum: Forum in Deutsch
Topic: Array lässt sich nicht mit Booleschen Operation abziehen
Replies: 9
Views: 180

Re: Array lässt sich nicht mit Booleschen Operation abziehen

Ohne die Datei ist es schwer etwas zu sagen, aber bei der Verwendung von Part-Funktionen musst Du immer den gesamten Body auswählen, nicht nur ein Feature daraus.
by chrisb
Tue Oct 26, 2021 4:40 pm
Forum: Help on using FreeCAD
Topic: Misalignment on polar pattern?
Replies: 8
Views: 258

Re: Misalignment on polar pattern?

Fillet, Chamfer and Draft are rather dressups, and as such the patterns need the feature which is dressed up as well.
by chrisb
Tue Oct 26, 2021 11:57 am
Forum: Forum in Deutsch
Topic: Kantteile modellieren
Replies: 6
Views: 343

Re: Kantteile modellieren

Das Problem mit einem Loft ist, dass es auch bei gleichbleibender Stärke mit der SheetMetal-Workbench nicht mehr flachgelegt werden kann, weil die Flächen B-Spline-Oberflächen werden. Geometriefehler wie z.B. bei Shalmeneser tun dann ihr Übriges. Ich würde tatsächlich SheetMetal versuchen und dann Ü...
by chrisb
Tue Oct 26, 2021 9:05 am
Forum: Path/CAM
Topic: GRBL new post processor with drill cycles G81..G83
Replies: 89
Views: 18097

Re: GRBL new post processor with drill cycles G81..G83

Without going into the code you can go over the input field and the help text popping up shows the parameters.
by chrisb
Tue Oct 26, 2021 9:00 am
Forum: Install / Compile
Topic: Launch from Windows installer fails to drop privileges
Replies: 112
Views: 14691

Re: Launch from Windows installer fails to drop privileges

You miss the point: What you call "improvement" would mean to get rid of the feature. I explained it quite often and you must admit that I was very patient. However at some point I cannot repeat again and again. If you don't like the feature, feel free to remove it but expect complaints f...