Search found 32 matches

Go to advanced search

by Walgri
Tue Apr 23, 2019 2:50 pm
Forum: FEM
Topic: Result mesh single element/node picking and inspection
Replies: 12
Views: 359

Re: Result mesh single element/node picking and inspection

The analysis mesh is made visibile when I click on the Select Point button.
by Walgri
Tue Apr 23, 2019 2:00 pm
Forum: FEM
Topic: Result mesh single element/node picking and inspection
Replies: 12
Views: 359

Re: Result mesh single element/node picking and inspection

bernd wrote:
Tue Apr 23, 2019 1:52 pm
As far as I remember StressVectors in VTK are vonMises stress! Again use 0.19, you will have all what you need there in result object :)
Thanks ! Will try !
by Walgri
Tue Apr 23, 2019 1:59 pm
Forum: FEM
Topic: Result mesh single element/node picking and inspection
Replies: 12
Views: 359

Re: Result mesh single element/node picking and inspection

Uh, I just noticed that the value shown in the dialog box is the same for any point and DisplacementeVectors or StressVectors.

Please check if the attached file is complete enough to point out that behaviour. Thanks !
by Walgri
Tue Apr 23, 2019 1:02 pm
Forum: FEM
Topic: Result mesh single element/node picking and inspection
Replies: 12
Views: 359

Re: Result mesh single element/node picking and inspection

Hi, I'm a bit lost here. I have sort-of managed to get the DataAtPoint, but I'm not sure what I'm getting, see attached screeshot: I was expecting a vector, not a scalar. Clipboard03.png Also, if I left-click on a result mesh face the Selection View (often, not always) reports a string like: freecad...
by Walgri
Thu Apr 18, 2019 12:01 pm
Forum: FEM
Topic: Result mesh single element/node picking and inspection
Replies: 12
Views: 359

Result mesh single element/node picking and inspection

Hello,

is it possible in the GUI to pick and inspect the result values of a single finite element or node ?

Thanks
by Walgri
Wed Apr 10, 2019 10:32 am
Forum: FEM
Topic: Building structural design workflow
Replies: 1
Views: 167

Building structural design workflow

HI, I would like to gather information, share points of view and learn how to possibly extend and consolidate the FEM Wb to improve the support for building struttural design workflow. One of the things I need almost every day is the ability to have mixed 1D and 2D FE meshes, that represent pillars,...
by Walgri
Tue Apr 02, 2019 4:51 pm
Forum: FEM
Topic: fcFEM - FEA from start to finish
Replies: 184
Views: 9367

Re: fcFEM - FEA from start to finish

It looks like GMSH is left without node reordering by design: http://onelab.info/pipermail/gmsh/2008/003717.html Plus, partially offtopic, is see no trace of node reordering in the OOFEM manual. Mhmmm, maybe we need a general node reordering intermediate step before writing input files and reading b...
by Walgri
Tue Apr 02, 2019 7:13 am
Forum: FEM
Topic: how to name different finite element meshes
Replies: 7
Views: 214

Re: how to name different finite element meshes

FWIW, I second @HarryvL: those seem to be the most univoque and unambigous descriptions.
by Walgri
Sat Mar 23, 2019 9:57 pm
Forum: Open discussion
Topic: Automate Reinforcement GSoC proposal
Replies: 197
Views: 13262

Re: Automate Reinforcement GSoC proposal

Hi, To me it looks natural that at a certain point the rebar addon (or a new Reinforced concrete addon) should be able to talk to the fem module results too, then design the reinforcement accordingly and perform the checks. I would add that code provisions may require (lots of) additional checks on ...
by Walgri
Fri Mar 22, 2019 1:47 pm
Forum: FEM
Topic: fcFEM - FEA from start to finish
Replies: 184
Views: 9367

Re: fcFEM - FEA from start to finish

I'm guessing the same after you described the BCs.

Edit: in the other pictures, the left face stays flat, so for sure it's a visualization issue.

Go to advanced search