Search found 2145 matches

Go to advanced search

by Jee-Bee
Wed Nov 25, 2020 4:07 pm
Forum: Assembly
Topic: Request for a separate Assy file format
Replies: 6
Views: 330

Re: Request for a separate Assy file format

NX have one format that could be anything and works fine to me. creo have 4 or more filetypes depend on what it is (part, assy, drawing, fem, ...). For me personal i don't care about it...
by Jee-Bee
Wed Nov 25, 2020 4:01 pm
Forum: Open discussion
Topic: Realthunders work
Replies: 29
Views: 1572

Re: Realthunders work

I don't think the problem that users don't see it... I think that the problem is that users read on the forum about new features that exist and are waiting to be merged. but the merging takes more than a half year (https://github.com/FreeCAD/FreeCAD/pull/2723 this one almost a year). Specially when ...
by Jee-Bee
Wed Nov 18, 2020 4:53 pm
Forum: Open discussion
Topic: Improving the Clipping plane functionality
Replies: 7
Views: 277

Re: Improving the Clipping plane functionality

Clipping plane is one of these features that should be available from everywhere. (just like measurement; etc; ...)
by Jee-Bee
Tue Nov 17, 2020 1:48 pm
Forum: Part Design module development
Topic: Hole dialog discussion
Replies: 119
Views: 4711

Re: Hole dialog discussion

Does it matter if they are on the marked or custom made?
If they exist in the norm add them to the tool. I expect that checking if there is a reseller it takes more time than just add it.
by Jee-Bee
Fri Nov 13, 2020 9:15 pm
Forum: Open discussion
Topic: Spreadsheet delete value possible bug
Replies: 7
Views: 245

Re: Spreadsheet delete value possible bug

AndrewCSP wrote:
Fri Nov 13, 2020 1:55 pm
The bug reporting system says in large caps
IMPORTANT: POST ONLY 0.19dev BUG REPORTS
but I am still using 0.18.
Should I ignore that headline?
Normaly if you think you found a bug... check the current 0.xx development version and check if the bug still exist.
by Jee-Bee
Fri Nov 13, 2020 9:12 pm
Forum: Install / Compile
Topic: MacOS BigSur
Replies: 18
Views: 1327

Re: FreeCAD Apple Silicon (ARM) support

you mean 11.xx?
by Jee-Bee
Fri Nov 13, 2020 8:30 pm
Forum: Install / Compile
Topic: MacOS BigSur
Replies: 18
Views: 1327

Re: FreeCAD Apple Silicon (ARM) support

At the moment openGL don't work anymore on OSX i think i sell my mac
by Jee-Bee
Fri Nov 13, 2020 7:33 am
Forum: Part Design module development
Topic: [Enhancing Loft] : abilty to use a point as section
Replies: 4
Views: 348

Re: [Enhancing Loft] : abilty to use a point as section

I remember some years back there was a kind of how to challenge what ends in a point... then I had the same issue that the point don't work. But I remember me vaguely that the problem was the sketcher. when creating a loft it handles the point from the draftwb well but the one from sketcher not. the...
by Jee-Bee
Fri Nov 13, 2020 7:16 am
Forum: Open discussion
Topic: Werner passes 7000 posts and other fascinating maths! :-)
Replies: 328
Views: 35434

Re: Werner passes 7000 posts and other fascinating maths! :-)

as long as 0.19 will be released it is the release with most commits
The former release was 0.17 (6832 commits) 0.19 have as of now 6837 commits. This is compared to 18.4 but it looks it is still changing a bit..
by Jee-Bee
Fri Nov 06, 2020 1:38 pm
Forum: FEM
Topic: hoisting problem FEM
Replies: 3
Views: 280

Re: hoisting problem FEM

2020-11-06 13_52_27-FreeCAD 0.19.png for the example just assume that it is hoisted above the bar. the red arrows are forces of the mass below the beam. the blue lines are the hoisting sling / chain / whatever is used. the green lines are the effect that i expect that would happen. My problem is mo...

Go to advanced search