Search found 40 matches

Go to advanced search

by mslonik
Sun Mar 06, 2016 6:58 pm
Forum: Help on using FreeCAD
Topic: Order of constraints is important
Replies: 5
Views: 697

Re: Order of constraints is important

Thank you for your replies. @NormandC: Please believe me, that I did. As the evidence I've provided link to a problem which I've found reading this forum and searching information about order of constraint. As it was pointed out my assumption was wrong - it's not about order of constraint (what I've...
by mslonik
Sun Mar 06, 2016 6:35 pm
Forum: Help on using FreeCAD
Topic: Order of constraints is important
Replies: 5
Views: 697

Re: Order of constraints is important

Thank you for your prompt reply. Sorry if my question is trivial, but how do you know that one of the contours is not closed; how have you found that? I'm asking this question to avoid this kind of drawbacks in future.

Kind regards, mslonik
by mslonik
Sun Mar 06, 2016 11:58 am
Forum: Help on using FreeCAD
Topic: Another confusion with symmetry constraint
Replies: 3
Views: 541

Re: Another confusion with symmetry constraint

Thank you for very prompt reply. Is there any advised work-flow which let to omit this kind of drawback and confusion? I mean, for example, to put at first one kind of constraints before another? Or maybe there is best practise rule to verify a sketch?

Kind regards, mslonik
by mslonik
Sun Mar 06, 2016 11:50 am
Forum: Help on using FreeCAD
Topic: Order of constraints is important
Replies: 5
Views: 697

Order of constraints is important

Dear Forum, I've found the following accompanying information at this forum: http://forum.freecadweb.org/viewtopic.php?t=13908&start=10 : However, users have also to learn to create robust sketches. Good constraints to use are: -Horizontal/vertical length. -Horizontal/vertical constraint. -Point/Poi...
by mslonik
Sun Mar 06, 2016 10:27 am
Forum: Help on using FreeCAD
Topic: Another confusion with symmetry constraint
Replies: 3
Views: 541

Another confusion with symmetry constraint

Dear Forum, At first let me explain why do I entitled this thread as "another" confusion. Well, it's because I've found one very similar thread ( http://forum.freecadweb.org/viewtopic.php?t=9189 ). Let me show you my problem and ask you for advise. My example is pretty abstract ( Exercise5.fcstd ), ...
by mslonik
Sat Mar 05, 2016 9:21 am
Forum: Help on using FreeCAD
Topic: Tools -> Save picture, strange behaviour
Replies: 11
Views: 2443

Re: Tools -> Save picture, strange behaviour

@bejant: Indeed thumbnails were switched off by default. Then I changed one of my project files, saved document and used Dolphin to see thumbnails. But there are no thumbnails at all. Next I've created completely new project containing just simple cube. Still no thumbnails. So it looks like jmaustpc...
by mslonik
Thu Mar 03, 2016 9:03 pm
Forum: Help on using FreeCAD
Topic: Pocket operation, Through All, strange behaviour
Replies: 10
Views: 1410

Re: Pocket operation, Through All, strange behaviour

Well, it seems that I was a bit too quick with posting at dev.opencascade.org. As I was informed: First of all, this is OCCT development forum, not OCE - it is unlikely you'll have some feedback from OCE developers on this forum (and OCE releases are not supported by Open CASCADE). The best way to r...
by mslonik
Thu Mar 03, 2016 8:46 pm
Forum: Help on using FreeCAD
Topic: Tools -> Save picture, strange behaviour
Replies: 11
Views: 2443

Re: Tools -> Save picture, strange behaviour

Look at your fcstd files in your operating system's standard file browser, i.e. in KDE "Dolphin" turn on thumb nail display which normally is by default, I think, for all file types, so when you look at a JPEG file etc. you see a thumb nail (small low resolution image of the image within the file)....
by mslonik
Wed Mar 02, 2016 8:31 pm
Forum: Help on using FreeCAD
Topic: Pocket operation, Through All, strange behaviour
Replies: 10
Views: 1410

Re: Pocket operation, Through All, strange behaviour

Ok, again thank you for your support. I've opened a thread about spotted problem also here: http://dev.opencascade.org/index.php?q=node/1150

Kind regards, mslonik
by mslonik
Wed Mar 02, 2016 8:10 pm
Forum: Python scripting and macros
Topic: MACRO:Work Feature 2014_12
Replies: 205
Views: 36898

Re: MACRO:Work Feature 2014_12

Just type RETURN into the "End tab, Ending Point: To define: X" Edit Line and "End tab, Ending Point: To define: Y" Edit Line in order to validate your changes and it will works It works :D That was trivial... Anyway I expected that after pressing "Apply" button selected values for X and Y will be ...

Go to advanced search