Search found 5323 matches
- Thu Dec 14, 2023 12:29 am
- Forum: Help on using FreeCAD
- Topic: Missing surfaces in step export
- Replies: 11
- Views: 5898
Re: Missing surfaces in step export
This worked as a work-around, but does any one know if there is going to be a fix for the bug any time soon? There cannot be a fix until the problem is defined. You can start by including a sample file that shows the problem, along with the detailed steps you take to get the bad result. This topic ...
- Thu Dec 14, 2023 12:16 am
- Forum: Path/CAM
- Topic: Masso G3 Post Processers
- Replies: 6
- Views: 4936
Re: Masso G3 Post Processers
I've been struggling with the issue of a post-processor for Masso on my onefinity Elite Journeyman using Freecad to surface my wasteboard. You did not respond to the ongoing discussion in your other current topic. In short, your sketch size is not what you said. It is bigger. You did not say what t...
- Wed Dec 13, 2023 3:03 pm
- Forum: Open discussion
- Topic: Sketcher: Prevent ostensible redundant constraint
- Replies: 18
- Views: 11534
- Wed Dec 13, 2023 2:54 pm
- Forum: Help on using FreeCAD
- Topic: Workaround for "ignored: macos mouse"?
- Replies: 3
- Views: 2193
Re: Workaround for "ignored: macos mouse"?
While searching the forums for help, I noticed that, to me, two important search terms were ignored, preventing me from restricting the number of search hits. This is a well-known but unfortunate limitation of the forum software, which FreeCAD does not control. The solution is to use your favorite ...
- Wed Dec 13, 2023 2:48 pm
- Forum: Open discussion
- Topic: PartDesign toolbar new sketch (new concept)
- Replies: 42
- Views: 37363
- Wed Dec 13, 2023 2:45 pm
- Forum: Open discussion
- Topic: Sticky FAQ
- Replies: 5
- Views: 3869
Re: Sticky FAQ
The bug submission sticky is thoroughly outdated. It should be removed or rewritten. (A sticky should not have 5 pages of discussion!)TheMarkster wrote: ↑Wed Dec 13, 2023 5:12 am It should go in Help section. There are only 3 stickies there.
Gene
- Wed Dec 13, 2023 2:40 pm
- Forum: Developers corner
- Topic: FreeCAD compatibility with Python 3.12
- Replies: 15
- Views: 12994
Re: FreeCAD compatibility with Python 3.12
I see this error message any time I try to "import" anything, either through a program line or directly by my action. DLL load failed while importing PathApp: The specified procedure could not be found. Traceback (most recent call last): File "D:\FreeCD\FreeCAD\FreeCAD_0.22\Mod\Path\...
- Wed Dec 13, 2023 2:28 pm
- Forum: Path/CAM
- Topic: 3-d surface.
- Replies: 15
- Views: 6057
Re: 3-d surface.
I would like to point out a bug that was discovered and was the cause of my torment - in the project shown, when there is only a solid, the first creation of a Path project can (exactly can) occur with the model created in one position (location) and the workpiece in another. This is what was causi...
- Wed Dec 13, 2023 2:17 pm
- Forum: Install / Compile
- Topic: Opencamlib on freecad 0.21.1
- Replies: 6
- Views: 4567
Re: Openlibcam on freecad 0.21.1
There is no need at all to "install" OCL. It comes with FreeCAD distributions. The wiki is outdated in that it says to install OCL. That requirement was removed several years ago. What IS needed is to EnableExperimentalFeatures , as detailed in the wiki. https://wiki.freecad.org/Path_expe...
- Wed Dec 13, 2023 2:11 pm
- Forum: Open discussion
- Topic: Sketcher: Prevent ostensible redundant constraint
- Replies: 18
- Views: 11534