Search found 65 matches

Go to advanced search

by tom
Fri Jul 27, 2018 2:39 pm
Forum: Install / Compile
Topic: FreeCAD for MacOS now more than 100 commits behind
Replies: 41
Views: 2271

Re: FreeCAD for MacOS now more than 100 commits behind

Log: Cannot mix incompatible Qt library (version 0x50b00) with this library (version 0x50b01) Does this mean that it loads two Qt versions at runtime or does it only mean that a library links against Qt 5.11.1 when 5.11.0 is expected (or the other way round)? I guess that latter one. IMHO following...
by tom
Thu Jul 26, 2018 5:55 pm
Forum: Install / Compile
Topic: FreeCAD for MacOS now more than 100 commits behind
Replies: 41
Views: 2271

Re: FreeCAD for MacOS now more than 100 commits behind

But there is also an error message complaining about incompatible QT versions: Log: Cannot mix incompatible Qt library (version 0x50b00) with this library (version 0x50b01) I think this is caused by a wrong line in .travis.yml QT5_CMAKE_PREFIX=$(ls -d $(brew --cellar)/qt/*/lib/cmake) This works only...
by tom
Mon May 14, 2018 10:55 pm
Forum: Help on using FreeCAD
Topic: Creating a simple part with PartDesign tutorial I'm stuck
Replies: 23
Views: 716

Re: Creating a simple part with PartDesign tutorial I'm stuck

I don't think that the issue is in my case related to a config format change from 0.16 to 0.17, because I regularly lose my toolbars when I update from one 0.17 version to another (or even 0.18). I believe that I also saw the problem without installing a new version. If remember correctly there was ...
by tom
Mon May 14, 2018 10:13 pm
Forum: Help on using FreeCAD
Topic: Creating a simple part with PartDesign tutorial I'm stuck
Replies: 23
Views: 716

Re: Creating a simple part with PartDesign tutorial I'm stuck

Somehow you have turned off your toolbars, The same thing happens to me regularly. I did not find a pattern yet, when this occurs, but most of the time it happens just after installing a new FreeCAD version. The suddenly all toolbars are gone and I have to reenable them. BR Thomas OS: Mac OS X Word...
by tom
Fri Mar 23, 2018 7:10 pm
Forum: Forum in Deutsch
Topic: Saubere PartDesign 0.17 Konstruktion
Replies: 58
Views: 3928

Re: Saubere PartDesign 0.17 Konstruktion

So, wie es aussieht, hat freecad-heini-1 die Part-O-Magic WB installiert. Wenn die installiert ist wird beim Speichern des Dokuments automatisch der Display Mode aller Bodies auf Tip geändert. In diesem Mode sieht man eben nur den Tip. Ändere also bitte den Display Mode des Bodies wieder auf Through...
by tom
Sat Jan 13, 2018 9:16 pm
Forum: Help on using FreeCAD
Topic: [PDN] Problem with additive pipe and multiple sections
Replies: 8
Views: 399

Re: [PDN] Problem with additive pipe and multiple sections

Hi NormandC, thank you for your effort and sorry for the confusion in the subject. I have corrected the subject in my previous posts now. Unfortunately the problem is a bit more complicated. As I mentioned in my first post there is no symmetry in the real part. The attached model was only a very sim...
by tom
Sat Jan 13, 2018 4:07 pm
Forum: Help on using FreeCAD
Topic: [PDN] Problem with additive pipe and multiple sections
Replies: 8
Views: 399

Re: [PDN] Problem with additive pipe and multiple sections

Ok, here is a new FC document showing the problem - this time without having part-o-magic installed.
by tom
Sat Jan 13, 2018 3:27 pm
Forum: Help on using FreeCAD
Topic: [PDN] Problem with additive pipe and multiple sections
Replies: 8
Views: 399

Re: [PDN] Problem with additive pipe and multiple sections

Hi chrisb, I know that zipping the FC file does not help to shrink the file, but it helped me to upload the file at all. If I do not zip the file, then I can't select the .FCStd file in the File section dialogue. Also dragging the file into the forum message box (as suggested in the forum) did not h...
by tom
Sat Jan 13, 2018 1:10 pm
Forum: Help on using FreeCAD
Topic: [PDN] Problem with additive pipe and multiple sections
Replies: 8
Views: 399

[PDN] Problem with additive pipe and multiple sections

Hi, I'm trying to create a part using the additive pipe tool in PDN. I want to loft the sketches001 to 004 along the selected path as shown in the picture. pdnSweepTest1.png All works fine, if I select only Sketch001 and Sketch002 and sweep along Edge1 of Sketch: pdnSweepTest2.png But as soon I add ...
by tom
Mon Aug 28, 2017 7:57 pm
Forum: Help on using FreeCAD
Topic: Crash opening file containing PDN hole feature
Replies: 5
Views: 434

Re: Crash opening file containing PDN hole feature

@wmayer: That was fast. Thank you so much. You saved my day.

Regards,
Thomas

Go to advanced search