Search found 582 matches

Go to advanced search

by bambuko
Wed Sep 08, 2021 5:33 pm
Forum: Help on using FreeCAD
Topic: search window in Tree view
Replies: 16
Views: 642

Re: search window in Tree view

...This sounds different from your OP... it is not a "preferred solution" if in order to use it I need to scroll to the top, and that was what I thought was the case (however, see below) ...Any click anywhere inside the Tree widget will give it the focus. worked it out, eventually (I am s...
by bambuko
Wed Sep 08, 2021 3:24 pm
Forum: Help on using FreeCAD
Topic: search window in Tree view
Replies: 16
Views: 642

Re: search window in Tree view

..."Ctrl+F" when tree has the focus. Yes, but... that's precisely what I am trying to avoid :) I have a tree "mile long" and I need to scroll up for it to be "in focus" , so this is no better (just different) than the current option of using right click and selecting f...
by bambuko
Wed Sep 08, 2021 1:47 pm
Forum: Help on using FreeCAD
Topic: search window in Tree view
Replies: 16
Views: 642

Re: search window in Tree view

thomas-neemann wrote: Wed Sep 08, 2021 12:49 pm only when I select the found part with enter instead of the mouse it disappears.
That sounds familiar ... :oops:
by bambuko
Wed Sep 08, 2021 12:21 pm
Forum: Help on using FreeCAD
Topic: search window in Tree view
Replies: 16
Views: 642

search window in Tree view

Is possible to have this window "on" and available all the time by default at the bottom of tree view? At the moment, every time I want to do a search I need to go to the top of the tree to right click and activate it (it dissapears soon after I finish searching... I haven't worked out why...
by bambuko
Sun Sep 05, 2021 7:11 am
Forum: Help on using FreeCAD
Topic: Are You Serious?
Replies: 23
Views: 1099

Re: Are You Serious?

chrisb wrote: Sat Sep 04, 2021 8:34 pm ...May I ask if you are serious? ...
Sorry for being blunt.
I admire your patience dealing with this kind of ignorance and bad attitude.
Don't be sorry ;) - you are not blunt enough...
by bambuko
Sun Aug 22, 2021 7:08 pm
Forum: Assembly
Topic: Designing model locomotive kits using Assembly and other workbenches
Replies: 6
Views: 1711

Re: Designing model locomotive kits using Assembly and other workbenches

...would be nice of sheetmetal workbench if apart from subtraction (cutting through) and folding, it also have etch function where you can specify areas of half edge from each side :) perhaps it would be nice...? but probably too complicated? Most of the guys doing it use something like https://qca...
by bambuko
Wed Aug 18, 2021 9:37 am
Forum: Assembly
Topic: Broken assembly3 file after Freecad's crash
Replies: 3
Views: 797

Re: Broken assembly3 file after Freecad's crash

...The first problem: I can't see two parts (PIPE002, PIPE003)... Opened sketches for these two parts, closed sketches and parts appeared fine. This is not to say that the sketches are any good... but that's another story. ...second problem: can't recompute whole asembly... There are problems with ...
by bambuko
Fri Aug 06, 2021 8:23 pm
Forum: Help on using FreeCAD
Topic: Left and Right do not make sense
Replies: 8
Views: 447

Re: Left and Right do not make sense

You are not the only one :mrgreen:
This might be of interest to you:
https://forum.freecadweb.org/viewtopic. ... 7&start=40
by bambuko
Fri Aug 06, 2021 12:34 pm
Forum: Open discussion
Topic: linkstage3 installation
Replies: 2
Views: 265

Re: linkstage3 installation

No, you do not have to install "official release". Just download either stable or daily (depending what you want), unzip to a directory/location of your choice. Find bin directory, and .exe inside and run it (you can create shortcut if you want). You can run it in parallel with "offic...
by bambuko
Fri Jul 30, 2021 5:25 pm
Forum: Open discussion
Topic: Realthunders work
Replies: 59
Views: 6600

Re: Realthunders work

chrisb wrote: Mon Jul 26, 2021 10:09 pm FreeCAD cannot do anything about that. This has to be handled in the branch.
It takes two to tango...

Go to advanced search