Search found 1991 matches
- Thu Feb 13, 2020 6:34 am
- Forum: Forum in Deutsch
- Topic: Probleme mit Aufdicken in Part und Part Design
- Replies: 13
- Views: 2196
Re: Probleme mit Aufdicken in Part und Part Design
… ich hab's auch hingekriegt - in PartWB mit 300kB - und obwohl ich ständig Schwierigkeiten mit Thickness bekomme. Nur Refinement geht nicht. Sind wohl noch ein paar verborgene "Besonderheiten" drin. Auch habe ich versucht, die Leitkurve und die Revolve-Kontur zur Vermeidung der Seed-Lines...
- Wed Feb 12, 2020 9:23 am
- Forum: Open discussion
- Topic: How can I "mirror" the placement of a part in FreeCAD
- Replies: 3
- Views: 361
Re: How can I "mirror" the placement of a part in FreeCAD
… you can also perform something like placement inside the mirror tool.
Now make an experiment and rightclick Mirror
Now make an experiment and rightclick Mirror
- Tue Feb 11, 2020 4:12 pm
- Forum: Open discussion
- Topic: [Feauture request] : abilty tangent constraint to a spline in sketcher
- Replies: 9
- Views: 3491
Re: [Feauture request] : abilty tangent constraint to a spline in sketcher
… point to point tangent works -
but try it between two BSplines or between the two ends of a BSpline ????
here (FC-0.18.4-WIN32)
That's a task I often have to do.
but try it between two BSplines or between the two ends of a BSpline ????
here (FC-0.18.4-WIN32)
That's a task I often have to do.
- Tue Feb 11, 2020 1:58 pm
- Forum: Open discussion
- Topic: [Feauture request] : abilty tangent constraint to a spline in sketcher
- Replies: 9
- Views: 3491
Re: [Feauture request] : abilty tangent constraint to a spline in sketcher
… if you connect the 1st and the 2nd control point of the sketcher BSpline with a (blue) construction line - or the last 2 points,
then you get a tangent constrainable feature.
then you get a tangent constrainable feature.
- Sun Feb 09, 2020 4:16 pm
- Forum: Help on using FreeCAD
- Topic: Theoretical question - why its not possible to Loft from Face to Face
- Replies: 13
- Views: 1237
Re: Theoretical question - why its not possible to Loft from Face to Face
… a very simple rule:
if the first solid has 4 edges then the second solid should also have 4 "edges",
then the loft is not "disturbed".
Have a look into the sketch.
If you work with PartWB, you can use Facebinder from DraftWB.
if the first solid has 4 edges then the second solid should also have 4 "edges",
then the loft is not "disturbed".
Have a look into the sketch.
If you work with PartWB, you can use Facebinder from DraftWB.
- Sun Feb 09, 2020 8:57 am
- Forum: Help on using FreeCAD
- Topic: Half Hull help
- Replies: 21
- Views: 2696
Re: Half Hull help
Hi John, … your hull is "overconstrained" by too much frames => Zellulite. The old fashioned boat designers used a wooden spline and some 4 weights to get a smooth curve. The sketcher BSpline has the same problem. 4 control points and you get a smooth curvature comb. If you use 5 controlpo...
- Fri Feb 07, 2020 7:08 am
- Forum: Forum in Deutsch
- Topic: Form um Rundung
- Replies: 34
- Views: 2693
Re: Form um Rundung
@Wilfried, ich habe mir dein Video angesehen und stelle fest, es gibt somit weitaus solidere Methoden zur Darstellung dieses "Kragens". Mir geht's momentan immer noch um dieses "OrientedSketch" aus der CurvesWB. Es ist festzustellen, dass sich der Sweep nicht unbedingt an die lok...
- Thu Feb 06, 2020 9:19 am
- Forum: Forum in Deutsch
- Topic: Form um Rundung
- Replies: 34
- Views: 2693
Re: Form um Rundung
… noch'n Gedicht bzgl. CurvesWB. Ich habe neulich mal das OrientedSketch-Tool ausprobiert. Ist zwar ein bisschen mehr Beinarbeit, da das 3D-Offset mal wieder zickt, aber durchaus interessant. Im Tool gibt es den Wert Parameter von 0,0 - 1,0 , mit dem kann man die Positionen von Duplikaten bestimmen....
- Thu Feb 06, 2020 6:08 am
- Forum: Forum in Deutsch
- Topic: Bildbeispiele von FreeCAD Projekten
- Replies: 5
- Views: 1063
Re: Bildbeispiele von FreeCAD Projekten
… KAPs Versuch, in Anlehnung an die jüngst geführte Diskussion zur Themenaufspaltung im deutschen Forum, sowas wie einen Showcase einzuführen, zieht wohl nicht so recht => jeder macht das vorzugsweise in eigenen Threads. Ich wüsste z.B. gerade nicht, wo ich das Folgende ohne Nekrobumping oder Thread...
- Tue Feb 04, 2020 5:12 pm
- Forum: Help on using FreeCAD
- Topic: Half Hull help
- Replies: 21
- Views: 2696
Re: Half Hull help
… I try to fill this post with links and usage examples: https://forum.freecadweb.org/viewtopic.php?t=32335#p332858 https://forum.freecadweb.org/viewtopic.php?f=8&t=22675&start=540#p359623 MFrame and MKeel are master-sketches which I duplicate for the local (by placement) sketches/frames. Th...