If there had been some thought put into the position of the model, it would be trivial to use a multitransform.
There is no file so, impossible to say if that is still a way forward.
Like this:-
Search found 4255 matches
- Thu Apr 11, 2024 5:23 pm
- Forum: Help on using FreeCAD
- Topic: Subtractive Pipe with multiple paths
- Replies: 7
- Views: 633
- Thu Apr 11, 2024 3:16 pm
- Forum: Help on using FreeCAD
- Topic: Corners on Sweep or additive pipe
- Replies: 5
- Views: 375
Re: Corners on Sweep or additive pipe
Set refine to true in the last feature.
- Thu Apr 11, 2024 8:37 am
- Forum: Open discussion
- Topic: Merge lattice WB as a tool in PD
- Replies: 21
- Views: 1458
- Wed Apr 10, 2024 8:17 pm
- Forum: Help on using FreeCAD
- Topic: how to make polar pattern from pockets around cylinder
- Replies: 17
- Views: 2443
Re: how to make polar pattern from pockets around cylinder
I just use the face of the thread for a sweep, but if you want to be rock solid, use the profile sketch. (It may mean changing the attachment/placement, and reversing the direction etc. YMMV.)
- Wed Apr 10, 2024 2:57 pm
- Forum: Help on using FreeCAD
- Topic: how to make polar pattern from pockets around cylinder
- Replies: 17
- Views: 2443
Re: how to make polar pattern from pockets around cylinder
The Pattern will slow the model down, better to keep the patterns at two instants of each until the model is complete. Then go into the properties and change to the required number.
Also it's important not to break the single solid rule, does the pattern fit properly?
Also it's important not to break the single solid rule, does the pattern fit properly?
- Wed Apr 10, 2024 7:13 am
- Forum: Help on using FreeCAD
- Topic: PartDesign - SubtractivePipe - ShapeBinder
- Replies: 13
- Views: 647
Re: PartDesign - SubtractivePipe - ShapeBinder
It is doable with SSB's, use an offset equal to the width of the cut face (-10mm) for the path.
Select the profile SSB in the 3D view then the tool, hide the pad and select the edges for the path from the path SSB.
Select the profile SSB in the 3D view then the tool, hide the pad and select the edges for the path from the path SSB.
- Wed Apr 10, 2024 6:51 am
- Forum: Help on using FreeCAD
- Topic: polar array
- Replies: 13
- Views: 759
Re: polar array
Change the rotation axis.....
- Tue Apr 09, 2024 7:04 pm
- Forum: Help on using FreeCAD
- Topic: [Solved] sketch: Center Line and symmetry
- Replies: 5
- Views: 468
Re: sketch: Center Line and symmetry
Applying symmetry constraint will cause an over-constraint situation, there are only 3 degrees of freedom left, the length of the lines and the distance from the axis. If the symmetry is required, delete the horizontal constraint on the three top points..... An added note if there is symmetry use it...
- Tue Apr 09, 2024 4:30 pm
- Forum: Help on using FreeCAD
- Topic: Boolean operation modifies PartDesign AdditivePipe
- Replies: 13
- Views: 647
Re: Boolean operation modifies PartDesign AdditivePipe
If it's any use I was able to get close in Part wb.....
- Tue Apr 09, 2024 2:52 pm
- Forum: Help on using FreeCAD
- Topic: how to make polar pattern from pockets around cylinder
- Replies: 17
- Views: 2443
Re: how to make polar pattern from pockets around cylinder
Don't hesitate to ask for more help.