you have at least 3 possibilities:
-Write a text as said above
-Write text in the drawing itself with Draft Wb
-Write text in a spreadsheet
Search found 7998 matches
- Fri Apr 12, 2024 7:08 am
- Forum: Help on using FreeCAD
- Topic: Comments and Notes in each Freecad file
- Replies: 4
- Views: 405
- Thu Apr 11, 2024 3:03 pm
- Forum: Help on using FreeCAD
- Topic: Corners on Sweep or additive pipe
- Replies: 5
- Views: 374
Re: Corners on Sweep or additive pipe
the profile must "wrap" around the path so that it does not have an auto intersection, and "transform" on "Right corners" (or round)
- Wed Apr 10, 2024 6:55 pm
- Forum: Help on using FreeCAD
- Topic: Arch Wall tool renders wrong, passes Geometry check
- Replies: 11
- Views: 884
Re: Arch Wall tool renders wrong, passes Geometry check
the masons of the XIV em did not ask themselves the question if Fc should join the right, the ends or the left
- Wed Apr 10, 2024 2:57 pm
- Forum: Help on using FreeCAD
- Topic: Unfolding Sheet Metal Failure
- Replies: 7
- Views: 438
Re: Unfolding Sheet Metal Failure
I don't see the point in making a plan of the blank, folding it then unfolding it Don't say that you are a beginner, when you read your sketch, you can see it (this is not a criticism) uses equalities, symmetry, alignment and finally everything that is geometric before the dimension and no =0mm unfo...
- Wed Apr 10, 2024 10:39 am
- Forum: Help on using FreeCAD
- Topic: Metal Bending, adjust angle of end
- Replies: 4
- Views: 447
Re: Metal Bending, adjust angle of end
attach the file, it seems that there is stuff before and stuff after
- Wed Apr 10, 2024 10:35 am
- Forum: Help on using FreeCAD
- Topic: Arch Wall tool renders wrong, passes Geometry check
- Replies: 11
- Views: 884
Re: Arch Wall tool renders wrong, passes Geometry check
no, it's better not, as you see it doesn't distribute the thicknesses correctly
do the T then the V, you can also easily manage the Middle, Right or left
Edit show my exemle
do the T then the V, you can also easily manage the Middle, Right or left
Edit show my exemle
- Wed Apr 10, 2024 8:48 am
- Forum: Help on using FreeCAD
- Topic: Constrain as currently laid out?
- Replies: 7
- Views: 598
Re: Constrain as currently laid out?
Trim breaks constraints in a sketch that was constrained, it's understandable: lengths, circles, symmetries are cut in two, it's frustrating, but there are no solutions
- Wed Apr 10, 2024 8:32 am
- Forum: Help on using FreeCAD
- Topic: PartDesign - SubtractivePipe - ShapeBinder
- Replies: 13
- Views: 646
Re: PartDesign - SubtractivePipe - ShapeBinder
if you do the sketches with sketcher (outside the Body),
there is no point doing Binders , ShapesBinder , Sub...., SubSub....
you drag the sketch with the tip of your mouse into the Body
to make the groove: if the radius is too small to risk self-intersection, you have to redo a path
there is no point doing Binders , ShapesBinder , Sub...., SubSub....
you drag the sketch with the tip of your mouse into the Body
to make the groove: if the radius is too small to risk self-intersection, you have to redo a path
- Wed Apr 10, 2024 7:51 am
- Forum: Forum français
- Topic: Coque de plusieurs révolutions
- Replies: 4
- Views: 428
- Tue Apr 09, 2024 8:25 pm
- Forum: Forum français
- Topic: Model Mania 2024 Phase 1
- Replies: 6
- Views: 486
Re: Model Mania 2024 Phase 1
tu veux dire que ma photo JPG te parais horrible , mais elle parai belle sur cet vue non c'est une capture d'écran
ou c'est dans mon fichier , il est fais dans une ancienne version
Edit : comme ça c'est mieux
ou c'est dans mon fichier , il est fais dans une ancienne version
Edit : comme ça c'est mieux