Search found 1985 matches

by hammax
Fri Feb 07, 2020 7:08 am
Forum: Forum in Deutsch
Topic: Form um Rundung
Replies: 34
Views: 2681

Re: Form um Rundung

@Wilfried, ich habe mir dein Video angesehen und stelle fest, es gibt somit weitaus solidere Methoden zur Darstellung dieses "Kragens". Mir geht's momentan immer noch um dieses "OrientedSketch" aus der CurvesWB. Es ist festzustellen, dass sich der Sweep nicht unbedingt an die lok...
by hammax
Thu Feb 06, 2020 9:19 am
Forum: Forum in Deutsch
Topic: Form um Rundung
Replies: 34
Views: 2681

Re: Form um Rundung

… noch'n Gedicht bzgl. CurvesWB. Ich habe neulich mal das OrientedSketch-Tool ausprobiert. Ist zwar ein bisschen mehr Beinarbeit, da das 3D-Offset mal wieder zickt, aber durchaus interessant. Im Tool gibt es den Wert Parameter von 0,0 - 1,0 , mit dem kann man die Positionen von Duplikaten bestimmen....
by hammax
Thu Feb 06, 2020 6:08 am
Forum: Forum in Deutsch
Topic: Bildbeispiele von FreeCAD Projekten
Replies: 5
Views: 1059

Re: Bildbeispiele von FreeCAD Projekten

… KAPs Versuch, in Anlehnung an die jüngst geführte Diskussion zur Themenaufspaltung im deutschen Forum, sowas wie einen Showcase einzuführen, zieht wohl nicht so recht => jeder macht das vorzugsweise in eigenen Threads. Ich wüsste z.B. gerade nicht, wo ich das Folgende ohne Nekrobumping oder Thread...
by hammax
Tue Feb 04, 2020 5:12 pm
Forum: Help on using FreeCAD
Topic: Half Hull help
Replies: 21
Views: 2663

Re: Half Hull help

… I try to fill this post with links and usage examples: https://forum.freecadweb.org/viewtopic.php?t=32335#p332858 https://forum.freecadweb.org/viewtopic.php?f=8&t=22675&start=540#p359623 MFrame and MKeel are master-sketches which I duplicate for the local (by placement) sketches/frames. Th...
by hammax
Tue Feb 04, 2020 2:12 pm
Forum: Help on using FreeCAD
Topic: Half Hull help
Replies: 21
Views: 2663

Re: Half Hull help

… boat design without BSplines - unthinkable => boatbuilders "invented" the BSpline.
Be careful, there are some tricks inside, caused by the diffuse draft.
The mirroring feature inside sketcher for the aft frames must be renewed after changes.

Nickolson_4.png
Nickolson_4.png (61.5 KiB) Viewed 746 times
by hammax
Tue Feb 04, 2020 6:02 am
Forum: Forum in Deutsch
Topic: Entfernt
Replies: 11
Views: 950

Re: Energieerzeugung statt Community Tonabnehmer für Plattenspieler

… Wenn das mal stimmt? Ich pflichte Chrisb bezüglich seiner Anmerkung über die "Gültigkeit" der Thermodynamischen Hauptsätze bei. Durch die enorme Hitze (ca. 3000°C) spaltet sich der molekulare Wasserstoff thermisch in atomaren Wasserstoff. Dabei wird sehr viel Energie frei Freiwerdende En...
by hammax
Mon Feb 03, 2020 7:24 am
Forum: Help on using FreeCAD
Topic: Half Hull help
Replies: 21
Views: 2663

Re: Half Hull help

… I suppose that your model hasn't the final scale.
Here a proposal for a workflow with FC, based on drawings as a reference
and using Sketcher-BSplines.
It is only a quick and dirty approach.
And a scale 1:20 preparation.
by hammax
Sun Feb 02, 2020 5:40 pm
Forum: Help on using FreeCAD
Topic: Half Hull help
Replies: 21
Views: 2663

Re: Half Hull help

… from the mesh-model it can't be seen. Is it a Venezian gondola or an ancient Egyptian boat?

Gondola.PNG
Gondola.PNG (36.88 KiB) Viewed 1317 times
by hammax
Sun Feb 02, 2020 12:38 pm
Forum: Forum in Deutsch
Topic: Bildbeispiele von FreeCAD Projekten
Replies: 5
Views: 1059

Re: Bildbeispiele von FreeCAD Projekten

… da bereitet einer im Help-Forum offensichtlich ein Valentinstag Geschenk für seine Liebste vor. https://forum.freecadweb.org/viewtopic.php?f=3&t=42942#p365116 (Wahrscheinlich soll nur die Akzeptanz für die Anschaffung des 3D-Druckers erhöht werden - happy wife, happy life). Das hat mir Gelegen...
by hammax
Sun Feb 02, 2020 7:52 am
Forum: Help on using FreeCAD
Topic: Half Hull help
Replies: 21
Views: 2663

Re: Half Hull help

… it is a little difficult, to get insight, which kind and size of boat you mean and what's your special problem with 3D-printing. Here some German links concerning racing sailing models => look for the pictures: https://forum.freecadweb.org/viewtopic.php?f=13&t=35212&start=40#p298991 https:...