since I'm a good grandpa, I'm going to show you something funny:
you select the upper face (oval) you Pad and at the end you obtain a new perfectly circular section and the same diameter as the base
Search found 8018 matches
- Tue Apr 23, 2024 12:54 pm
- Forum: Help on using FreeCAD
- Topic: PartDesign Thickness doesn't cross planes?
- Replies: 3
- Views: 162
- Tue Apr 23, 2024 12:42 pm
- Forum: Help on using FreeCAD
- Topic: PartDesign Thickness doesn't cross planes?
- Replies: 3
- Views: 162
Re: PartDesign Thickness doesn't cross planes?
I don't understand why you are multiplying posts on the same subject
ask the question 15 times you will get the same question 14 times same reply plus one who did not understand
ask the question 15 times you will get the same question 14 times same reply plus one who did not understand
- Tue Apr 23, 2024 12:34 pm
- Forum: Help on using FreeCAD
- Topic: Sketch fully constrained, but still not
- Replies: 3
- Views: 79
Re: Sketch fully constrained, but still not
best practice: turn this Line in blue (Line construction) and do the fillets in the sketch
more: use equality
more: use equality
- Tue Apr 23, 2024 9:41 am
- Forum: Help on using FreeCAD
- Topic: Joining two cylinders at an angle
- Replies: 7
- Views: 335
Re: Joining two cylinders at an angle
Edit of Edit : delete your other post since it was answered here
- Tue Apr 23, 2024 9:25 am
- Forum: Help on using FreeCAD
- Topic: Joining two cylinders at an angle
- Replies: 7
- Views: 335
Re: Joining two cylinders at an angle
if you want you can do a zigzag
don't forget to specify "transition > right corners"
Edit: With the latest version, there is no more self intersection with "Round corner" good news
don't forget to specify "transition > right corners"
Edit: With the latest version, there is no more self intersection with "Round corner" good news
- Tue Apr 23, 2024 9:12 am
- Forum: Help on using FreeCAD
- Topic: Sheet metal extend to create angled edge for slope-faced cabinet
- Replies: 8
- Views: 411
Re: Sheet metal extend to create angled edge for slope-faced cabinet
I understood what you want
I don't start with PartDesign, that causes problems when you have cuts to make, so I use Sketcher and SheetMetal, if necessary PartWb for angled cuts
I don't start with PartDesign, that causes problems when you have cuts to make, so I use Sketcher and SheetMetal, if necessary PartWb for angled cuts
- Tue Apr 23, 2024 8:07 am
- Forum: Forum français
- Topic: Se dépanner d'un problème freecad
- Replies: 5
- Views: 186
Re: Se dépanner d'un problème freecad
quand tu fais "Copier" une fenètre s'ouvre et te montre tous ce qui est susceptible d'être copier , tu décoche ce que tu veux pas emmener et fouette cocher , mais t'inquiète pas si t'as deux fois le plan XY , le second ne gènera pas si c'est pour faire un système à glissières à double queu...
- Mon Apr 22, 2024 3:56 pm
- Forum: Help on using FreeCAD
- Topic: Fusion not working fully/properly?
- Replies: 23
- Views: 884
Re: Fusion not working fully/properly?
I reread the entire post until my eyes bleed, but I don't see a file anywhere
- Sun Apr 21, 2024 1:30 pm
- Forum: Help on using FreeCAD
- Topic: Sheet metal extend to create angled edge for slope-faced cabinet
- Replies: 8
- Views: 411
Re: Sheet metal extend to create angled edge for slope-faced cabinet
everything goes well up to "BaseWall" why do an extrusion over the already existing folding
- Sun Apr 21, 2024 1:03 pm
- Forum: Forum français
- Topic: TechDraw : comment faire pour coter en mètre et non en millimètres ??
- Replies: 5
- Views: 278
Re: TechDraw : comment faire pour coter en mètre et non en millimètres ??
ha oui Ok , mais fouchtrah ça marche pas , ça passe en inch, en Ft, en cm arch mais pas en m