+1 for your comprehensive approach on this. Don't be discouraged.
Search found 228 matches
- Tue Sep 21, 2021 4:34 am
- Forum: UX/UI Design
- Topic: My take on the FreeCAD GUI
- Replies: 253
- Views: 81293
- Sun Aug 29, 2021 1:33 pm
- Forum: Job offers
- Topic: Open Hardware licenced anti-tremor cup
- Replies: 10
- Views: 16323
Re: Open Hardware licenced anti-tremor cup
Jep, there are not that much products around. I found this one: https://www.youtube.com/watch?v=mM9_Ol4K-bA This handles just one axis and seems to work (more or less). Regarding the springs you have to consider resonances. This might be a dead end. With a heavy tremor using your favourite mug might...
- Sun Aug 29, 2021 5:31 am
- Forum: Job offers
- Topic: Open Hardware licenced anti-tremor cup
- Replies: 10
- Views: 16323
Re: Open Hardware licenced anti-tremor cup
Are those spirals ment to be flextures? Could make sense if the final product should be 3D printable. Otherwise this will be quite complicated to keep it clean. I have no idea regarding health care products. But, are you re-inventing the wheel? I would think that products like this are ready availab...
- Mon Aug 09, 2021 9:37 am
- Forum: Open discussion
- Topic: FreeCAD association → FreeCAD cooperative!
- Replies: 22
- Views: 5603
Re: FreeCAD association → FreeCAD cooperative!
@LibrEars: Checked your PN lately?
- Fri Aug 06, 2021 3:45 pm
- Forum: Open discussion
- Topic: SOL75 3D customizer
- Replies: 0
- Views: 1390
SOL75 3D customizer
Just found this.
https://hackaday.com/2021/07/19/sol75-u ... cal-parts/
https://www.sol75.com/
Wasn't there a post regardings something similar, recently?
Greetings, Mark
https://hackaday.com/2021/07/19/sol75-u ... cal-parts/
https://www.sol75.com/
Wasn't there a post regardings something similar, recently?
Greetings, Mark
- Fri Aug 06, 2021 2:46 pm
- Forum: Help on using FreeCAD
- Topic: Linkstage3 UI: can't move Property View to another monitor
- Replies: 4
- Views: 1103
Re: Linkstage3 UI: can't move Property View to another monitor
I questioned this issue here ...
https://forum.freecadweb.org/viewtopic. ... 81#p502881
... but I did not follow-up so far.
https://forum.freecadweb.org/viewtopic. ... 81#p502881
... but I did not follow-up so far.
- Mon May 10, 2021 11:15 am
- Forum: Assembly
- Topic: Assembly3 preview
- Replies: 2024
- Views: 1377760
Re: Assembly3 preview
Yes, I will. I just asked for confirmation that is no problem on my side ... or the solution is obvious (except for me )
- Mon May 10, 2021 11:04 am
- Forum: Assembly
- Topic: Assembly3 preview
- Replies: 2024
- Views: 1377760
Linkbranch on Win10: Dragging panels out of main window fails
There is no separate Linkbranch subforum so I am posting this here. I am used to pull panels out of the main window on my dual-monitor setup like this: ksnip_20210510-124603.png This does not work with Linkbranch. The panels are just flipping back to the main window. I am pretty sure that this was d...
- Fri May 07, 2021 7:06 am
- Forum: Forum in Deutsch
- Topic: Spreadsheet cell update dauert 1:10
- Replies: 9
- Views: 1423
Re: Spreadsheet cell update dauert 1:10
Hast du mal probeweise "Fillet002" entfernt. Die Fehlermeldung in meiner Version mag ja ein Hinweis sein.
- Thu May 06, 2021 12:52 pm
- Forum: Forum in Deutsch
- Topic: Spreadsheet cell update dauert 1:10
- Replies: 9
- Views: 1423
Re: Spreadsheet cell update dauert 1:10
Aus eigener Erfahrung und falls du das nicht ohnehin probiert hast: FC neu starten. Ich fahre W10 nur in den Standy und habe FC dann teilweise über Tage offen mit verschiedenen Projekten. Sobald etwas wirklich komisch ist starte ich FC neu und sehr oft ist das Thema erledigt. Edit: Neuberechnung kla...