Search found 35709 matches

by chrisb
Tue Aug 03, 2021 7:03 am
Forum: Help on using FreeCAD
Topic: Visibility toggle not working after CheckGeometry
Replies: 19
Views: 972

Re: Visibility toggle not working after CheckGeometry

Gift wrote: Tue Aug 03, 2021 6:53 am Is the issue still relevant? I can not reproduce it currently. In the past I had the same problem.
I will check this later. Currently I have to repair an old model, which is all of a sudden broken, probably due to a change in OCC version.
by chrisb
Tue Aug 03, 2021 5:55 am
Forum: Help on using FreeCAD
Topic: how to connect or refer a sketch to the geometry of another body
Replies: 12
Views: 284

Re: how to connect or refer a sketch to the geometry of another body

giant1114 wrote: Tue Aug 03, 2021 1:32 am I can see the "shapebinder" but I assume the vertex of the line I draw should snap to the shape binder but it doesn't.
A vertex doesn't snap all by its own. You have to use the shapebinder together with Sketcher External.
by chrisb
Tue Aug 03, 2021 5:51 am
Forum: Wiki
Topic: Concerns From a User's Perspective
Replies: 23
Views: 1435

Re: Concerns From a User's Perspective

MSOlsen65 wrote: Tue Aug 03, 2021 12:46 am So once I get the new drive installed, I should operational in less than an hour. :mrgreen:
Good luck!
by chrisb
Mon Aug 02, 2021 10:08 pm
Forum: Help on using FreeCAD
Topic: how to connect or refer a sketch to the geometry of another body
Replies: 12
Views: 284

Re: how to connect or refer a sketch to the geometry of another body

The most frequent error with ShapeBinders is, that their source is still visible and then you cannot select them. I recommend to make everything invisible except the ShapeBinder..
by chrisb
Mon Aug 02, 2021 9:30 pm
Forum: Help on using FreeCAD
Topic: Pocket and slot at an angle
Replies: 13
Views: 322

Re: Pocket and slot at an angle

Shalmeneser wrote: Mon Aug 02, 2021 9:13 pm Where have you discovered this trick ?
I had tried to understand how attachment works, and played with the various attachment modes by creating appropriate models. However, i didn't have the feeling to fully understand attachment, and thus I haven't written yet about it.
by chrisb
Mon Aug 02, 2021 9:20 pm
Forum: Help on using FreeCAD
Topic: Pocket and slot at an angle
Replies: 13
Views: 322

Re: Pocket and slot at an angle

TheMarkster wrote: Mon Aug 02, 2021 9:07 pm Perhaps I am misunderstanding.
I was not precise: A MapPath-value between 0 and 1 is always on the edge, 0 at the start, 1 at the end.
by chrisb
Mon Aug 02, 2021 9:17 pm
Forum: Forum in Deutsch
Topic: Abrundung fräsen
Replies: 1
Views: 61

Re: Abrundung fräsen

Hallo und willkommen im Forum.
Solche Fräspfade werden in der Path-Workbench erzeugt. Für solch eine Abrundung würde ich die 3D-Surface-Funktion verwenden.
by chrisb
Mon Aug 02, 2021 8:51 pm
Forum: Forum in Deutsch
Topic: 2. Versuch: Projekt Bilderrahmen [Anfänger]
Replies: 40
Views: 1556

Re: 2. Versuch: Projekt Bilderrahmen [Anfänger]

Zunächst mal solltest Du alle im Body verwendeten Klone auch in den Body schieben. Der Dependency Graph zeigt Dir mit roten Pfeilen warum. Ich habe mal zur Demonstration nur ein Zwischen-Sketch direkt oberhalb des Bodens und eines knapp unterhalb des oberen Rands platziert. Die dienen nur dazu, die ...
by chrisb
Mon Aug 02, 2021 7:43 pm
Forum: Forum in Deutsch
Topic: 2. Versuch: Projekt Bilderrahmen [Anfänger]
Replies: 40
Views: 1556

Re: 2. Versuch: Projekt Bilderrahmen [Anfänger]

Frösch wrote: Mon Aug 02, 2021 6:59 pm Das wäre dann tatsächlich die Datei aus meinem letzten Post.
Die hatte ich übersehen, meistens stehen die Modelle ganz am Ende eines Beitrags. Wenn ich Zeit habe, schaue ich mir das mal an.
by chrisb
Mon Aug 02, 2021 7:41 pm
Forum: Help on using FreeCAD
Topic: how to connect or refer a sketch to the geometry of another body
Replies: 12
Views: 284

Re: how to connect or refer a sketch to the geometry of another body

LHC wrote: Mon Aug 02, 2021 6:12 pm Man, that's a huge emoji :lol:
The emojis still are huge when using the FreeCAD theme; it's ok in prosilver. This has to be fixed in the css file. I have made a proposal, but it is not implemented yet.