SlopedPlanesMacro

Show off your FreeCAD projects here!
damian
Posts: 583
Joined: Sun May 31, 2015 6:16 pm

SlopedPlanesMacro

Postby damian » Mon Nov 13, 2017 7:17 am

Good morning Community
Today I'll show you my progress with the tool SlopedPlanes.
damian
Posts: 583
Joined: Sun May 31, 2015 6:16 pm

Re: SlopedPlanesMacro

Postby damian » Mon Nov 13, 2017 7:43 am

Simple figures
instance_ONE.png
instance_ONE.png (29.6 KiB) Viewed 7658 times
And yes, this is a simple extrusion but the user can select a different extrusion direction or angle for every plane.
damian
Posts: 583
Joined: Sun May 31, 2015 6:16 pm

Re: SlopedPlanesMacro

Postby damian » Mon Nov 13, 2017 5:45 pm

A figure could have several wires and faces. The limit is the FaceMaker.
instance_TWO.png
instance_TWO.png (37.1 KiB) Viewed 7606 times
damian
Posts: 583
Joined: Sun May 31, 2015 6:16 pm

Re: SlopedPlanesMacro

Postby damian » Mon Nov 13, 2017 6:14 pm

The tool has options: Up, Down, Symmetry, Solid, Reverse, Complement, Tolerance y FaceMaker
instance_THREE.png
instance_THREE.png (123.63 KiB) Viewed 7595 times
The angles are controlled from the TaskPanel
damian
Posts: 583
Joined: Sun May 31, 2015 6:16 pm

Re: SlopedPlanesMacro

Postby damian » Mon Nov 13, 2017 6:54 pm

The figures could have reflex corner
instance_FOUR.png
instance_FOUR.png (41.2 KiB) Viewed 7586 times
User avatar
DeepSOIC
Posts: 6528
Joined: Fri Aug 29, 2014 12:45 am
Location: Saint-Petersburg, Russia

Re: SlopedPlanesMacro

Postby DeepSOIC » Mon Nov 13, 2017 7:06 pm

Looks very cool. I saw you were working with curves as well. Does it support curves?
User avatar
microelly2
Posts: 4244
Joined: Tue Nov 12, 2013 4:06 pm
Contact:

Re: SlopedPlanesMacro

Postby microelly2 » Mon Nov 13, 2017 7:12 pm

very interesting for geodata LOD roof design
damian
Posts: 583
Joined: Sun May 31, 2015 6:16 pm

Re: SlopedPlanesMacro

Postby damian » Mon Nov 13, 2017 7:36 pm

The two planes involved in a reflex corner act "like a dam". They block the progress of other planes.
instance_FIVE.png
instance_FIVE.png (39.61 KiB) Viewed 7562 times
damian
Posts: 583
Joined: Sun May 31, 2015 6:16 pm

Re: SlopedPlanesMacro

Postby damian » Mon Nov 13, 2017 7:48 pm

One edge could grow two faces
instance_SIX.png
instance_SIX.png (35.7 KiB) Viewed 7556 times
damian
Posts: 583
Joined: Sun May 31, 2015 6:16 pm

Re: SlopedPlanesMacro

Postby damian » Mon Nov 13, 2017 8:37 pm

DeepSOIC wrote:
Mon Nov 13, 2017 7:06 pm
Does it support curves?
Today no. Soon!
Now I found a mistake and I can't continue with the exposition. The problems of the direct.
The next week more
Thanks to everybody