Copy,Move and mirror elements in Sketch
Forum rules
and Helpful information
and Helpful information
IMPORTANT: Please click here and read this first, before asking for help
Also, be nice to others! Read the FreeCAD code of conduct!
Also, be nice to others! Read the FreeCAD code of conduct!
-
- Posts: 17
- Joined: Sat May 23, 2015 8:04 pm
Copy,Move and mirror elements in Sketch
Hi,
If possible to move, copy and mirror the elemtents in the Sketch Workbench.
Thanks
Marco
If possible to move, copy and mirror the elemtents in the Sketch Workbench.
Thanks
Marco
Re: Copy,Move and mirror elements in Sketch
No.marcorhinotec wrote:Hi,
If possible to move, copy and mirror the elemtents in the Sketch Workbench.
Thanks
Marco
But you can use some "workarounds". For example:
Move:
To move "block" of sketcher geometry constrain it first up to a point it will allow you to do that.
Copy:
First create one sketch and after use Edit -> Duplicate selection on it. Select both sketches and use Part Design -> Merge sketches.
Mirror:
Maybe there is a way as i didn’t investigate in depth. But you will probably want to do something with the created sketch after it is finished. For example add Pad or Pocket Feature. There are tools to mirror that (individual features and parts)!
Last edited by triplus on Sun Jul 12, 2015 10:21 am, edited 1 time in total.
-
- Posts: 17
- Joined: Sat May 23, 2015 8:04 pm
Re: Copy,Move and mirror elements in Sketch
You're welcome.marcorhinotec wrote:Thanks
P.S. Maybe this features will be implemented in Sketcher WB in the future. For example copy/paste would probably make sense. But this is low priority as Sketcher WB primary function is adding and containing sketcher geometry and for this work flow features like mirror make less sense. Symmetry constraints are therefore probably what you are after!
-
- Posts: 161
- Joined: Mon Feb 01, 2021 7:22 pm
Re: Copy,Move and mirror elements in Sketch
Using 0.19, this functionality is now available!
1. If you in part design workbench etc, first goto the sketch workbench.
2. Then left click drag to select an area.
3. Then see these buttons:
- The left tool bar button is mirror, the right one is for clone/copy/move This is where I found it: https://wiki.freecadweb.org/Sketcher_Clone
1. If you in part design workbench etc, first goto the sketch workbench.
2. Then left click drag to select an area.
3. Then see these buttons:
- The left tool bar button is mirror, the right one is for clone/copy/move This is where I found it: https://wiki.freecadweb.org/Sketcher_Clone
Re: Copy,Move and mirror elements in Sketch
You replied to a 6 years old topic .
A Sketcher Lecture with in-depth information is available in English, auf Deutsch, en français, en español.
-
- Posts: 161
- Joined: Mon Feb 01, 2021 7:22 pm
Re: Copy,Move and mirror elements in Sketch
Because the forum rules tell one to search before asking, and I searched for exactly this, and read this answer, and tried to apply it, it didnt go so well, so I read the help wiki, and discovered a better/more recent answer, so the next person who comes along will see the updated answer
Re: Copy,Move and mirror elements in Sketch
I see. There is only the danger of reviving dead horses.
A Sketcher Lecture with in-depth information is available in English, auf Deutsch, en français, en español.
Re: Copy,Move and mirror elements in Sketch
Is not a dead horse to a new rider... None of the suggestions above work for me... I have a sketch (file attached)...
I want to copy the item, flip it 90 degrees, and move the flipped copy to within about 2 mm of the original. I can copy it, I can clone it, etc. but when I do that, I cannot flip it or move it.
I have tried it unconstrained, fully constrained, padded, unpadded, etc. Haven't tried inside out, but would if I could. In the time I've spent trying to figure this out, I could have drawn a few hundred copies and tweaked them all to be identical.
I want to copy the item, flip it 90 degrees, and move the flipped copy to within about 2 mm of the original. I can copy it, I can clone it, etc. but when I do that, I cannot flip it or move it.
I have tried it unconstrained, fully constrained, padded, unpadded, etc. Haven't tried inside out, but would if I could. In the time I've spent trying to figure this out, I could have drawn a few hundred copies and tweaked them all to be identical.
- Attachments
-
- NahlBinding.FCStd
- (12.98 KiB) Downloaded 40 times
Last edited by dkolars on Wed Nov 03, 2021 8:11 pm, edited 1 time in total.
OS: Ubuntu 20.04.3 LTS (XFCE/xubuntu)
64-bit
Version: 0.19.24291 (Git) AppImage
Python version: 3.8.8
Qt version: 5.12.9
Coin version: 4.0.0
OCC version: 7.4.0
Locale: English/United States (en_US)
64-bit
Version: 0.19.24291 (Git) AppImage
Python version: 3.8.8
Qt version: 5.12.9
Coin version: 4.0.0
OCC version: 7.4.0
Locale: English/United States (en_US)
Re: Copy,Move and mirror elements in Sketch
dkolars, ....