Challenges?

Post here for help on using FreeCAD's graphical user interface (GUI).
Forum rules
and Helpful information
IMPORTANT: Please click here and read this first, before asking for help

Also, be nice to others! Read the FreeCAD code of conduct!
User avatar
thomas-neemann
Veteran
Posts: 11801
Joined: Wed Jan 22, 2020 6:03 pm
Location: Osnabrück DE 🇩🇪
Contact:

Re: Challenge?

Post by thomas-neemann »

papyblaise wrote: Fri Jun 24, 2022 7:59 am I don't understand what Thomas did ...
I will link a video to it
Gruß Dipl.-Ing. (FH) Thomas Neemann

https://www.youtube.com/@thomasneemann5 ... ry=freecad
User avatar
FBXL5
Posts: 979
Joined: Sat Aug 03, 2019 8:45 pm

Re: Challenge?

Post by FBXL5 »

thomas-neemann wrote: Fri Jun 24, 2022 7:29 am I think this is a good time. can you upload the file to learn from it?
Why not. I didn't save the file and had to recreate it, it may look a bit different now.
Attachments
Challenge-20220624.png
Challenge-20220624.png (211.21 KiB) Viewed 4133 times
Challenge-20220624.FCStd
(91.69 KiB) Downloaded 36 times
User avatar
papyblaise
Veteran
Posts: 7870
Joined: Thu Jun 13, 2019 4:28 pm
Location: France

Re: Challenge?

Post by papyblaise »

I went to recharge my batteries by eating a handful of cherries in my garden, and, in a few minutes and a single Wb
Attachments
999-1.FCStd
(86.75 KiB) Downloaded 39 times
Bance
Veteran
Posts: 4186
Joined: Wed Feb 11, 2015 3:00 pm
Location: London

Re: Challenge?

Post by Bance »

About 10-15mins...

Strangely the first pocket fails if the polar pattern is applied to last three ops YMMV.
Attachments
Snip macro screenshot-41c60f.png
Snip macro screenshot-41c60f.png (16.79 KiB) Viewed 4092 times
challengeBance.FCStd
(99.71 KiB) Downloaded 48 times
User avatar
thomas-neemann
Veteran
Posts: 11801
Joined: Wed Jan 22, 2020 6:03 pm
Location: Osnabrück DE 🇩🇪
Contact:

Re: Challenge?

Post by thomas-neemann »

Bance wrote: Fri Jun 24, 2022 11:17 am ...
the part looks relatively easy, but has its pitfalls
Gruß Dipl.-Ing. (FH) Thomas Neemann

https://www.youtube.com/@thomasneemann5 ... ry=freecad
User avatar
kwahoo
Posts: 680
Joined: Fri Nov 29, 2013 3:09 pm
Contact:

Re: Challenge?

Post by kwahoo »

3:03:
phpBB [video]

challeng1.FCStd
(140.5 KiB) Downloaded 41 times
Image
User avatar
thomas-neemann
Veteran
Posts: 11801
Joined: Wed Jan 22, 2020 6:03 pm
Location: Osnabrück DE 🇩🇪
Contact:

Re: Challenge?

Post by thomas-neemann »

kwahoo wrote: Fri Jun 24, 2022 10:14 pm ...
wonderful, you're the fastest so far.

here is mine at 3:20

https://www.youtube.com/watch?v=tVnGnqkYSaw

phpBB [video]
Last edited by thomas-neemann on Sat Jun 25, 2022 7:27 am, edited 1 time in total.
Gruß Dipl.-Ing. (FH) Thomas Neemann

https://www.youtube.com/@thomasneemann5 ... ry=freecad
chrisb
Veteran
Posts: 53920
Joined: Tue Mar 17, 2015 9:14 am

Re: Challenge?

Post by chrisb »

thomas-neemann wrote: Sat Jun 25, 2022 4:59 am wonderful, you're the fastest so far. can you link a video of it?
How many videos does it need :lol: ?
A Sketcher Lecture with in-depth information is available in English, auf Deutsch, en français, en español.
User avatar
Willem
Veteran
Posts: 1852
Joined: Fri Aug 12, 2016 3:27 pm
Location: Lisse, The Netherlands

Re: Challenge?

Post by Willem »

First time I see that Draft Upgrade can make Solids. This feature is also not mentioned in the Freecad documentation page https://wiki.freecadweb.org/Draft_Upgrade
User avatar
thomas-neemann
Veteran
Posts: 11801
Joined: Wed Jan 22, 2020 6:03 pm
Location: Osnabrück DE 🇩🇪
Contact:

Re: Challenge?

Post by thomas-neemann »

chrisb wrote: Sat Jun 25, 2022 6:25 am ...
How many videos does it need :lol: ?
if there was no video editing software to cut out pauses for thought, I suspect about 10
Gruß Dipl.-Ing. (FH) Thomas Neemann

https://www.youtube.com/@thomasneemann5 ... ry=freecad
Post Reply