Hisa Solver /Tutorial is not running
Moderator: oliveroxtoby
Forum rules
and Helpful information for the FEM forum
and Helpful information for the FEM forum
Hisa Solver /Tutorial is not running
Hello all,
First of all, i really thanks to Oliver Oxtoby, who is one of the developers of Hisa solver and moderator in here, to share this grate source.
I try to learn the solver, so i am trying some of the tutorial cases. Flatplate worked without problem but onereM6 is not runnig. I suspect of installation error, because there were some warning that may occur a problem. I attached output of the setupMesh and runSim commands.
Any help will be appreciated.
Have good days!
First of all, i really thanks to Oliver Oxtoby, who is one of the developers of Hisa solver and moderator in here, to share this grate source.
I try to learn the solver, so i am trying some of the tutorial cases. Flatplate worked without problem but onereM6 is not runnig. I suspect of installation error, because there were some warning that may occur a problem. I attached output of the setupMesh and runSim commands.
Any help will be appreciated.
Have good days!
- Attachments
-
- setupMesh.log
- (1.25 KiB) Downloaded 76 times
-
- runSim.log
- (14.61 KiB) Downloaded 88 times
- oliveroxtoby
- Posts: 837
- Joined: Fri Dec 23, 2016 9:43 am
- Location: South Africa
Re: Hisa Solver /Tutorial is not running
Thanks for reporting. It should be fixed.hllbls wrote: ↑Tue Jun 01, 2021 9:06 am Hello all,
First of all, i really thanks to Oliver Oxtoby, who is one of the developers of Hisa solver and moderator in here, to share this grate source.
I try to learn the solver, so i am trying some of the tutorial cases. Flatplate worked without problem but onereM6 is not runnig. I suspect of installation error, because there were some warning that may occur a problem. I attached output of the setupMesh and runSim commands.
Any help will be appreciated.
Have good days!
Re: Hisa Solver /Tutorial is not running
When will it be ? Should i cut off of my hisa solver works ?
- oliveroxtoby
- Posts: 837
- Joined: Fri Dec 23, 2016 9:43 am
- Location: South Africa
Re: Hisa Solver /Tutorial is not running
Re: Hisa Solver /Tutorial is not running
It works without a problem, thanks.
Re: Hisa Solver /Tutorial is not running
Hello Mr. Oliver,
I am curious about something in your Oneram6 tutorial case; why did you give a (0 0 0) to U value for freestream bc, i think it should be equal to internalValue. If you can enligten me, i would be very happy.
Have good days.
I am curious about something in your Oneram6 tutorial case; why did you give a (0 0 0) to U value for freestream bc, i think it should be equal to internalValue. If you can enligten me, i would be very happy.
Have good days.
- oliveroxtoby
- Posts: 837
- Joined: Fri Dec 23, 2016 9:43 am
- Location: South Africa
Re: Hisa Solver /Tutorial is not running
You are right, but it shouldn't make much difference as this value is replaced by the computed one the first time the boundary is updated.
Re: Hisa Solver /Tutorial is not running
Thanks for the quick reply.
How is the performance of the HiSA for unstructured tetrahedral meshes ? Do you have any studies on this issue ?
How is the performance of the HiSA for unstructured tetrahedral meshes ? Do you have any studies on this issue ?
Re: Hisa Solver /Tutorial is not running
I tested with my own mesh which is higly non-orthogonal unstructured tetrahedral meshes. it perfectly works.
Thanks for sharing this great source.
Thanks for sharing this great source.
Re: Hisa Solver /Tutorial is not running
Hello Mr. Oliver i just realized something: The formula you used in tutorial cases about 'k' seems to be wrong. You defined as "3/2*I*U^2" instead of "3/2*(I*U)^2" . I have to pay attention to initial conditions because my meshs are fully made of tet meshs, so it is so sensitive to init conditions.
Could you explain why did you use this formula or is there any mistake ?
Have good days!
Could you explain why did you use this formula or is there any mistake ?
Have good days!