Vote for IfcOpenShell and open source authoring workflows

This forum section is only for IFC-related issues
Post Reply
User avatar
Moult
Posts: 321
Joined: Sat Jan 05, 2019 11:46 am
Contact:

Vote for IfcOpenShell and open source authoring workflows

Post by Moult »

Thomas Krijnen, developer of IfcOpenShell, which powers FreeCAD (and BlenderBIM) has put forward a presentation proposal for the buildingSMART Oslo summit, on the topic of IfcOpenShell and open source authoring workflows - A presentation of the work happening in FreeCAD, BlenderBIM and IfcOpenShell towards authoring capabilities for end-users. .

Click on this link and press the like button to cast your vote if you think it's awesome and the world needs to know about it :) You will be required to enter in your name and email to vote.

https://technical.buildingsmart.org/ide ... workflows/

The vote button is kinda weird - only click the "like" button once and wait for the pop-up. Then enter in your details manually (do not copy paste) and press submit and wait for the pop-up to disappear. Then refresh the page and you will be logged in (check top right). Then you can press the like button again.

There are, of course, other presentations too that have been submitted, which you can browse here: https://technical.buildingsmart.org/oslo-presentations/
freecad-blenderbim.jpg
freecad-blenderbim.jpg (112.56 KiB) Viewed 26430 times
I also blog about 3D rendering, architecture, software and other on thinkMoult.com. RSS / Atom feed available for your convenience.
User avatar
yorik
Founder
Posts: 13640
Joined: Tue Feb 17, 2009 9:16 pm
Location: Brussels
Contact:

Re: Vote for IfcOpenShell and open source authoring workflows

Post by yorik »

Voted!
paullee
Veteran
Posts: 5097
Joined: Wed May 04, 2016 3:58 pm

Re: Vote for IfcOpenShell and open source authoring workflows

Post by paullee »

Not sure if voted successfully? :D
User avatar
Kunda1
Veteran
Posts: 13434
Joined: Thu Jan 05, 2017 9:03 pm

Re: Vote for IfcOpenShell and open source authoring workflows

Post by Kunda1 »

Voted. For some reason i was able to vote on https://technical.buildingsmart.org/oslo-presentations/ and not on the URL in the OP.

Edit: @Moult I've made this thread 'sticky' so it gets maximum exposure ;)
Alone you go faster. Together we go farther
Please mark thread [Solved]
Want to contribute back to FC? Checkout:
'good first issues' | Open TODOs and FIXMEs | How to Help FreeCAD | How to report Bugs
User avatar
Moult
Posts: 321
Joined: Sat Jan 05, 2019 11:46 am
Contact:

Re: Vote for IfcOpenShell and open source authoring workflows

Post by Moult »

Just keeping everyone updated:
London, (March 3, 2020) – Due to coronavirus disease (COVID-19), buildingSMART International (bSI) and buildingSMART Norway (bSN) have postponed the International Standards Summit that was due to take place between 23-26 March 2020 in Lillestrøm, Norway. The event has been rescheduled at the same location for the week 8-11, June 2020.
Source: https://www.buildingsmart.org/the-build ... i=84245608
I also blog about 3D rendering, architecture, software and other on thinkMoult.com. RSS / Atom feed available for your convenience.
triplus
Veteran
Posts: 9471
Joined: Mon Dec 12, 2011 4:45 pm

Re: Vote for IfcOpenShell and open source authoring workflows

Post by triplus »

Hi @Moult

Note that i relinked the nice image:

https://forum.freecadweb.org/viewtopic.php?f=8&t=43484
User avatar
Moult
Posts: 321
Joined: Sat Jan 05, 2019 11:46 am
Contact:

Re: Vote for IfcOpenShell and open source authoring workflows

Post by Moult »

Just updating again! We're going to present! Check details here: https://community.osarch.org/discussion ... ual-summit thank you so much everyone for all the support!
I also blog about 3D rendering, architecture, software and other on thinkMoult.com. RSS / Atom feed available for your convenience.
User avatar
Moult
Posts: 321
Joined: Sat Jan 05, 2019 11:46 am
Contact:

Re: Vote for IfcOpenShell and open source authoring workflows

Post by Moult »

I also blog about 3D rendering, architecture, software and other on thinkMoult.com. RSS / Atom feed available for your convenience.
Post Reply