输出*.stl文件后,分辨率降低,请教如何解决?
Moderator: paullee
Forum rules
论坛规矩 / 論壇規矩 , 有用的资讯 / 有用的資訊
论坛规矩 / 論壇規矩 , 有用的资讯 / 有用的資訊
-
- Posts: 3
- Joined: Mon May 11, 2020 7:16 am
输出*.stl文件后,分辨率降低,请教如何解决?
准备3D打印,可是发现输出*.stl文件后,分辨率降低,请教如何解决?
Re: 输出*.stl文件后,分辨率降低,请教如何解决?
If you need help from others, please help others understand what you need.
Please provide: version info, screenshot, sample file.
-
- Posts: 3
- Joined: Mon May 11, 2020 7:16 am
Re: 输出*.stl文件后,分辨率降低,请教如何解决?
Thank you fc_tofu.
FreeCAD Ver. 0.18
This is the screenshot of .stl exported from the solid part.
You can see the arrowed part which is supposed to be a smooth circle, but the resolution was lowered once I did export file to .stl format that is not fit for 3D printing.
FreeCAD Ver. 0.18
This is the screenshot of .stl exported from the solid part.
You can see the arrowed part which is supposed to be a smooth circle, but the resolution was lowered once I did export file to .stl format that is not fit for 3D printing.
- Attachments
-
- 屏幕快照 2020-05-12 上午10.57.48.png (31.36 KiB) Viewed 9334 times
Re: 输出*.stl文件后,分辨率降低,请教如何解决?
You didnot give a sample file. So I use PartWB cylinder primitive as test example.
The topology of exported mesh is basically same as Rendering mode >Hiden line (Tesselation). The setup of tesselation is located at Pref >Part Design >Shape View >Maximun deviation. Default value is 0.5%, you can try a lower value, 0.1% or so, to get finer display/export.
-
- Posts: 3
- Joined: Mon May 11, 2020 7:16 am
Re: 输出*.stl文件后,分辨率降低,请教如何解决?
This is very helpful. Problem resolved, thanks again fc_tofu.
fc_tofu wrote: ↑Tue May 12, 2020 5:14 amYou didnot give a sample file. So I use PartWB cylinder primitive as test example.
The topology of exported mesh is basically same as Rendering mode >Hiden line (Tesselation).
fsc_2020-05-12_125912.jpg
The setup of tesselation is located at Pref >Part Design >Shape View >Maximun deviation. Default value is 0.5%, you can try a lower value, 0.1% or so, to get finer display/export.
fsc_2020-05-12_125847b.jpg
Re: 输出*.stl文件后,分辨率降低,请教如何解决?
盡量用中文吧,讓其它人也可以明白和參予 ,中英夾雜也無妨
Re: 输出*.stl文件后,分辨率降低,请教如何解决?
各位好,我有類似的問題,我在Tinkercad畫一物件,匯出stl後要列印但不夠平滑,所以才接觸freecad,我在fc匯入後然後依上述更改設定後,看起來並沒有變得更平滑,請問該如何解決呢? 謝謝。
*使用fc版本為0.19
*使用fc版本為0.19