Curved Shapes Workbench
Forum rules
Be nice to others! Read the FreeCAD code of conduct!
Be nice to others! Read the FreeCAD code of conduct!
Re: Curved Shapes Workbench
The vertexes are not aligned, you should redraw the sketches or use joincurve. Joincurve have a offset option now is need.
Corner break parameter can be used as well.
Corner break parameter can be used as well.
- Attachments
-
- CurvedSegment.FCStd
- (19.96 KiB) Downloaded 60 times
-
- Capture.JPG (24.9 KiB) Viewed 2836 times
-
- Capture2.JPG (57.24 KiB) Viewed 2836 times
Re: Curved Shapes Workbench
Hi Zolko and GlouGlou,
As you found out, the Twist parameter did not work with sketches that have more than one line segment.
Creating a join curve solves this by 1. creating a single curve and 2. moving the starting point to the top.
For those who do not know this trick and to get rid of the problem with the twist parameter, I have implemented Zolkos approach to reorder the line segments. The twist parameters will now reorder the line segments instead of the pole points of the lines. If you have 6 line segments, you can apply twists with a multiple of 60 degrees. I think this will work for most designs.
Check out the new version of the CurvedShapes Workbench.
As you found out, the Twist parameter did not work with sketches that have more than one line segment.
Creating a join curve solves this by 1. creating a single curve and 2. moving the starting point to the top.
For those who do not know this trick and to get rid of the problem with the twist parameter, I have implemented Zolkos approach to reorder the line segments. The twist parameters will now reorder the line segments instead of the pole points of the lines. If you have 6 line segments, you can apply twists with a multiple of 60 degrees. I think this will work for most designs.
Check out the new version of the CurvedShapes Workbench.
Re: Curved Shapes Workbench
Hi,
InterpolatedMiddle doesn't work with this file. Or I missed something?
InterpolatedMiddle doesn't work with this file. Or I missed something?
- Attachments
-
- interpolated.FCStd
- (15.21 KiB) Downloaded 60 times
-
- Posts: 9
- Joined: Sat Nov 14, 2020 2:03 pm
cuvres WB shrunk my work?
so it look sliek it shurnk one side and grew the otherside in length how do i fix this?
- Attachments
-
- Handle.FCStd
- (157.91 KiB) Downloaded 54 times
-
- bottom.png (94.59 KiB) Viewed 2668 times
Last edited by Kunda1 on Fri Nov 20, 2020 5:22 am, edited 1 time in total.
Reason: Mod note: thread merged in to the main Curves Workbench thread
Reason: Mod note: thread merged in to the main Curves Workbench thread
Re: Curves workbench
krazywulf1983 wrote: ↑Fri Nov 20, 2020 2:08 am so it look sliek it shurnk one side and grew the otherside in length how do i fix this?
Mod note:
@krazywulf1983 your thread was merged in to the main Curves Curved Shapes WB thread. Please always paste your full About info in to posts you're asking assistance with. Please edit the above post to do just that. Thank you
Last edited by Kunda1 on Fri Nov 20, 2020 11:24 am, edited 1 time in total.
Reason: Curved Shapes not Curves workbench
Reason: Curved Shapes not Curves workbench
Alone you go faster. Together we go farther
Please mark thread [Solved]
Want to contribute back to FC? Checkout:
'good first issues' | Open TODOs and FIXMEs | How to Help FreeCAD | How to report Bugs
Please mark thread [Solved]
Want to contribute back to FC? Checkout:
'good first issues' | Open TODOs and FIXMEs | How to Help FreeCAD | How to report Bugs
Re: Curves workbench
This user uses Curved Shapes WB, not Curves.Kunda1 wrote: ↑Fri Nov 20, 2020 5:25 amkrazywulf1983 wrote: ↑Fri Nov 20, 2020 2:08 am so it look sliek it shurnk one side and grew the otherside in length how do i fix this?
Mod note:
@krazywulf1983 your thread was merged in to the main Curves WB thread. Please always paste your full About info in to posts you're asking assistance with. Please edit the above post to do just that. Thank you
Re: Curved Shapes Workbench
:facepalm:
Ok, fixed. Apologies.
Ok, fixed. Apologies.
Alone you go faster. Together we go farther
Please mark thread [Solved]
Want to contribute back to FC? Checkout:
'good first issues' | Open TODOs and FIXMEs | How to Help FreeCAD | How to report Bugs
Please mark thread [Solved]
Want to contribute back to FC? Checkout:
'good first issues' | Open TODOs and FIXMEs | How to Help FreeCAD | How to report Bugs
Re: cuvres WB shrunk my work?
Select the Sketch BottomFront and select BoundingBox in the View menu. Your base item BottomFront is bigger than the sides Sketch004 in y direction. This is why it is shrunk. To fix this, make a copy of Sketch004 and move the bars so they will cross the boundung box of BottomFront.krazywulf1983 wrote: ↑Fri Nov 20, 2020 2:08 am so it look sliek it shurnk one side and grew the otherside in length how do i fix this?
Re: Curved Shapes Workbench
How does one get the "Items" (shown in orange) to follow the hull curve rather than be parallel to the "Base"?
And what controls the last couple items? Is it possible to have them scale (not sure scale is the right word...) so they fit between the hull curves?
OS: Ubuntu 20.04.1 LTS (XFCE/ubuntustudio)
Word size of OS: 64-bit
Word size of FreeCAD: 64-bit
Version: 0.19.
Build type: Release
Branch: unknown
Hash: b082c813f820ebdb837ba6ace4b9124f9a73cc4a
Python version: 3.8.5
Qt version: 5.12.8
Coin version: 4.0.0
OCC version: 7.3.0
Locale: English/United States (en_US)
And what controls the last couple items? Is it possible to have them scale (not sure scale is the right word...) so they fit between the hull curves?
OS: Ubuntu 20.04.1 LTS (XFCE/ubuntustudio)
Word size of OS: 64-bit
Word size of FreeCAD: 64-bit
Version: 0.19.
Build type: Release
Branch: unknown
Hash: b082c813f820ebdb837ba6ace4b9124f9a73cc4a
Python version: 3.8.5
Qt version: 5.12.8
Coin version: 4.0.0
OCC version: 7.3.0
Locale: English/United States (en_US)
Star Trek II: The Wrath of Khan: Spock: "...His pattern indicates two-dimensional thinking."