Curves workbench

Have some feature requests, feedback, cool stuff to share, or want to know where FreeCAD is going? This is the place.
Forum rules
Be nice to others! Read the FreeCAD code of conduct!
User avatar
Chris_G
Posts: 1260
Joined: Tue Dec 31, 2013 4:10 pm
Location: France
Contact:

Re: Curves workbench

Postby Chris_G » Fri Feb 14, 2020 10:05 pm

Thanks Saso.
I wasn't sure it was a good solution either.
And I understand the drawbacks.
I will think about a better method.
User avatar
hammax
Posts: 1033
Joined: Thu Jan 19, 2017 5:03 pm
Location: Ammersee

Re: Curves workbench

Postby hammax » Sun Feb 16, 2020 7:58 am

… trying to build a "closed" (periodic?) Gordon surface there seems to be a minimalistic gap condition,
controlled by the tolerance value. If tolerance is 0,005 the gap must be greater (e.g. 0,01mm).
It is possible to make a closed shape by 2 Gordon surfaces.
https://forum.freecadweb.org/viewtopic. ... 63#p369150
Is there a way at all, to close sketches after building Gordon?

GordonClosed.PNG
GordonClosed.PNG (61.98 KiB) Viewed 336 times
Attachments
GordonClosed.FCStd
(28.58 KiB) Downloaded 6 times
freecad-heini-1
Posts: 6621
Joined: Tue Jan 07, 2014 11:10 am
Contact:

Re: Curves workbench

Postby freecad-heini-1 » Sun Feb 16, 2020 8:30 am

hammax wrote:
Sun Feb 16, 2020 7:58 am
… trying to build a "closed" (periodic?) Gordon surface there seems to be a minimalistic gap condition,
controlled by the tolerance value. If tolerance is 0,005 the gap must be greater (e.g. 0,01mm).
It is possible to make a closed shape by 2 Gordon surfaces.
https://forum.freecadweb.org/viewtopic. ... 63#p369150
Is there a way at all, to close sketches after building Gordon?


GordonClosed.PNG
Exactly the same topic interested me, using a Sweep on two Rails. Which possibility is there to get a "closed" surface?
User avatar
microelly2
Posts: 4627
Joined: Tue Nov 12, 2013 4:06 pm
Contact:

Re: Curves workbench

Postby microelly2 » Sun Feb 16, 2020 9:08 am

freecad-heini-1 wrote:
Sun Feb 16, 2020 8:30 am
Exactly the same topic interested me, using a Sweep on two Rails. Which possibility is there to get a "closed" surface?
There are different ways to get a closed layout.
Here an example in 2D
close_curve.FCStd
(13.03 KiB) Downloaded 14 times

Code: Select all

pts=[v.Point for v in App.ActiveDocument.Sketch.Shape.Wires[0].Vertexes]

bc=Part.BSplineCurve()
poles=pts
mults=[4,1,1,1,4]
knots=range(len(mults))
bc.buildFromPolesMultsKnots(poles,mults,knots,False,3)
Part.show(bc.toShape())


bc=Part.BSplineCurve()
poles=pts+[pts[0]]
mults=[4,1,1,1,1,4]
knots=range(len(mults))
bc.buildFromPolesMultsKnots(poles,mults,knots,False,3)
Part.show(bc.toShape())


bc=Part.BSplineCurve()
poles=pts+[pts[0]]
mults=[1,1,1,1,1,1,1,1,1]
knots=range(len(mults))
bc.buildFromPolesMultsKnots(poles,mults,knots,True,3)
Part.show(bc.toShape())


bc=Part.BSplineCurve()
poles=pts+[pts[0],pts[0]]
mults=[1,1,1,1,1,1,1,1,1,1]
knots=range(len(mults))
bc.buildFromPolesMultsKnots(poles,mults,knots,True,3)
Part.show(bc.toShape())


bc=Part.BSplineCurve()
poles=pts
mults=[1,1,1,1,1,1,1,1]
knots=range(len(mults))
bc.buildFromPolesMultsKnots(poles,mults,knots,True,3)
Part.show(bc.toShape())




freecad-heini-1
Posts: 6621
Joined: Tue Jan 07, 2014 11:10 am
Contact:

Re: Curves workbench

Postby freecad-heini-1 » Sun Feb 16, 2020 9:12 am

Ich habe sowas gemeint:
curves_wb_sweep_on_two_rails_full_circle_2.FCStd
(39.81 KiB) Downloaded 10 times
Die Kreisbögen in den beiden Sketchen habe ich mit 1mm Spalt erzeugt, aber sie sollen geschlossen sein.
User avatar
Chris_G
Posts: 1260
Joined: Tue Dec 31, 2013 4:10 pm
Location: France
Contact:

Re: Curves workbench

Postby Chris_G » Sun Feb 16, 2020 10:05 am

Currently, Gordon surface doesn't work for closed surfaces.
I hope I can add this feature someday.
freecad-heini-1
Posts: 6621
Joined: Tue Jan 07, 2014 11:10 am
Contact:

Re: Curves workbench

Postby freecad-heini-1 » Sun Feb 16, 2020 4:57 pm

GlouGlou wrote:
Fri Feb 07, 2020 8:33 pm
A suggested tool: select the two yellow edges, then make a tangent arc. Just need the radius.
Could be called "TangentArc" :D
saw here :https://www.youtube.com/watch?v=6IkXAcz ... ex=16&t=0s
Hello GlouGlou and others,
I tried to follow the example in Freecad. The faces, Connect and Split / Slice are good, but as soon as you start rounding the faces, Freecad behaves strange. It trims away surfaces in places that should be preserved. Who can show how to round these surfaces with R10 to R30mm?

Many greetings
Wilfried
Surface_with_Fillet_example.FCStd
(21.15 KiB) Downloaded 7 times
Fillet003 is strange:
Surface_with_Fillet_example_fillet003.FCStd
(37.76 KiB) Downloaded 7 times
No problem with a solid:
Surface_with_Fillet_example_solid.FCStd
(67.92 KiB) Downloaded 7 times
The problem are the orange faces. It's needed to sew them:
orange_faces_sewed.png
orange_faces_sewed.png (34.21 KiB) Viewed 242 times
https://forum.freecadweb.org/viewtopic. ... 74#p239574
User avatar
GlouGlou
Posts: 2010
Joined: Sun Apr 05, 2015 9:02 am
Location: La Rochelle, France

Re: Curves workbench

Postby GlouGlou » Sun Feb 16, 2020 6:40 pm

Sometimes Part tools carry out surfaces upside downed :roll: . But We are not able to see them until make an offset3D.
By using "reverse shapes" (PartWb) we can give the right direction for all faces.
Then Connect can be refined. and Fillet works better. :D
Hope It can help you.
Attachments
UpSideDown.JPG
UpSideDown.JPG (33.3 KiB) Viewed 227 times
Surfaces.FCStd
(45.06 KiB) Downloaded 5 times
User avatar
GlouGlou
Posts: 2010
Joined: Sun Apr 05, 2015 9:02 am
Location: La Rochelle, France

Re: Curves workbench

Postby GlouGlou » Sun Feb 16, 2020 6:48 pm

here the exercise. ;)
Attachments
zzz.FCStd
(274.26 KiB) Downloaded 16 times
Capture.JPG
Capture.JPG (33.85 KiB) Viewed 224 times
freecad-heini-1
Posts: 6621
Joined: Tue Jan 07, 2014 11:10 am
Contact:

Re: Curves workbench

Postby freecad-heini-1 » Sun Feb 16, 2020 9:16 pm

Thank you so much GlouGlou, the surface direction, good to know.